Land Rover Discovery 1 Parts

Sump Plug for the engine oil sump drain. Fitted to the sump drain port and removed at each oil change to drain the engine oil. The sealing washer ...

Baulk Ring for the R380 5-speed manual gearbox synchromesh assembly. The baulk ring (also known as the synchromesh ring) is the friction cone elem...

Crankshaft Damper for the 300TDi 2.5L turbo diesel engine, mounted on the front nose of the crankshaft. This torsional vibration damper absorbs th...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Power Steering Pipe - Box to Reservoir from the power steering hydraulic circuit, for the 200TDi engine. This low-pressure return pipe carries flu...

Heater Hose for the 200TDi engine cooling and heating circuit. This hose routes coolant from the engine cooling system to the cabin heater matrix,...

Heater Hose - Outlet returns engine coolant from the cabin heating circuit back to the engine cooling system after it has passed through the heater...

Heater Hose - Inlet carries engine coolant into the cabin heating circuit, feeding the heater matrix that warms air inside the HVAC housing. On th...

Bonnet Striker is part of the bonnet latch mechanism — the striker that the bonnet catch engages to hold the bonnet closed. When the bonnet is shu...

Distributor Vacuum Advance Unit for the 2-pin electronic distributor on the 3.5L V8 petrol engine. The vacuum unit mounts on the side of the distr...

Brake Caliper - front, left-hand side, for the solid (non-vented) front disc arrangement. The caliper carries the brake pads and the hydraulic pis...

Upper Link Bush Set - Polyurethane for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. Supplied as a set of two ...

Crankshaft Pulley for the 300 TDi 2.5L 4-cylinder turbo diesel, mounted on the nose of the crankshaft at the front of the engine. The pulley trans...

Grab Handle in black, an interior assist handle that mounts to the roof trim rail. It provides occupants with a secure handhold when entering or e...

Half Shaft Shim is a 1.05mm selective shim used in the front axle drive shaft and hub assembly. It sets the endfloat of the front half shaft drive...

Front flange LT230

Camshaft for the five-bearing four-cylinder engine, running in the cylinder block as the core of the overhead-valve valvetrain. Driven from the cr...

Intermediate & Rear Exhaust Assembly forms the rear section of the exhaust system, comprising the intermediate pipe and rear silencer. Install...

Throttle Potentiometer Gasket seals the throttle position sensor (throttle potentiometer) to the throttle body on the V8 EFI system. It forms the ...

Oil Separator Drain Hose for the crankcase ventilation system on the 2.5L naturally aspirated diesel and 200TDi turbo diesel engines. It drains th...

Rear Screen Wiper Motor with Mounting Bracket for the rear wash/wipe system. The motor drives the rear wiper arm across the tailgate glass. Suppli...

Battery Tray is the offside (right-hand) carrier tray that supports and locates the battery in the engine bay. It forms the mounting platform on w...

Fuel Tank Sender Wrench is a special service tool for the fuel tank sender unit assembly. It engages the metal locking ring that retains the fuel ...

Glass mirror D1, D2 RH

Accelerator Cable for EFI engines - left-hand drive applications. This cable runs from the accelerator pedal to the throttle body, transmitting pe...

Front Bumper - facelift-specification front bumper forming the leading structural and styling member of the front body. It bolts to the chassis fro...

Oxygen Sensor (lambda sensor) for the V8 EFI petrol exhaust system on catalyst-equipped applications. It measures residual oxygen in the exhaust ga...

ABS Pump Relay for the Anti-lock Braking System electrical circuit. A normally open, black-bodied relay that controls power supply to the ABS pump...

Distributor Drive Gear - V8

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Spring Retaining Plate for the front coil spring suspension. The plate seats the upper end of the front coil spring against the chassis spring seat...

Brake Light Switch operates the stop lamps within the braking system's electrical circuit. Mounted at the brake pedal, the switch closes when the ...

Brake Hose - Front - D1

Crankshaft Pulley Bolt for the 2.5L 300TDi diesel engine. This bolt secures the crankshaft pulley and torsional vibration damper to the nose of the...

Upper Front Swivel Pin for the front axle swivel housing assembly. The upper swivel pin bolts to the top of the swivel housing and forms the upper...

Intercooler Hose for the 200 TDi turbocharged induction system. Part of the charge-air ducting that links the intercooler into the boost circuit, ...

Automatic Transmission Oil Screen for the ZF 4-speed automatic transmission, fitted within the transmission oil sump. The screen filters the autom...

Bump Stop - rear suspension bump stop that limits the upward travel of the axle at full compression. The moulded rubber block cushions the contact ...

Release Bearing Guide - the guide sleeve in the clutch release mechanism, mounted on the front cover of the manual gearbox. It encircles the gearb...

Anti-Roll Bar is the rear stabiliser bar within the suspension system, mounted transversely across the rear axle. Connected to the suspension thro...

Body Mount Spacer Tube forms part of the body-to-chassis mounting assembly, located at a mount point between the body and the chassis frame. It se...

Plain Washer - a flat load-spreading washer used at the body-to-chassis mount fixings. Fitted under the bolt head or nut, it distributes clamping ...

Crankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...

Outer Shim - 1.35mm - Front Halfshaft / CV Joint This 1.35mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Engine Cooling Fan - 11-blade, 17-inch diameter mechanical fan for the engine cooling system. Driven from the front of the engine via a viscous co...

Washer Pump draws fluid from the washer reservoir and delivers it to the windscreen jets. Mounted in the base of the washer bottle, this pump serv...

Front Left-Hand Indicator Lamp Assembly for the Discovery 1. This amber turn signal lamp unit is mounted at the front left corner of the vehicle a...

Clutch Damper for 200TDi and 300TDi diesel engines. This in-line hydraulic damper fits within the clutch hydraulic hose run between the master cyl...