Land Rover Discovery 2 Parts

Flywheel Assembly for the 2.5L Td5 five-cylinder turbo diesel engine, mounted between the engine and the manual gearbox. Bolted to the rear of the...

Cooler Oil

Manifold Absolute Pressure (MAP) Sensor, part of the engine management system. The MAP sensor measures the absolute pressure inside the intake man...

Tow Ball – 50 mm a black-finished towing ball for flange-type towing brackets. The ball bolts to the face of the towing bracket on the standard tw...

Bleed Hose is a small-bore coolant hose within the expansion tank and hose assembly of the engine cooling system. It connects the expansion tank t...

Braided Brake Hose Kit, extended by 150mm, covering the flexible sections of the hydraulic brake circuit between the chassis-mounted brake pipes an...

Steel hex full nut, M8 x 1.25 thread, catalogued for the clutch and dual-mass flywheel assembly on the Td5 2.5L 5-cylinder turbo diesel engine. Th...

Cam Follower - a roller-type tappet operating in the engine valve train, between the camshaft and the pushrod. It rides on the camshaft lobe and t...

Banjo Bolt for the turbocharger oil feed pipe on the Td5 engine. This M12 x 1.0mm thread banjo bolt clamps the hollow banjo fitting of the oil sup...

Blade Fuse - 25A for Land Rover electrical systems. This 25A blade fuse protects individual circuits in the vehicle fuse box from overcurrent damage.

Big End Bearing Set — connecting-rod (big-end) bearing shells for the V8 engine bottom end. The shells sit between the connecting-rod big-end bore...

Nyloc Nut - M16 for use in the front axle steering knuckle assembly. This M16 self-locking nut uses a nylon insert to provide prevailing-torque re...

Oil Pressure Switch for the V8 petrol engine. The switch monitors oil pressure in the engine lubrication circuit and activates the instrument clus...

Self-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...

Rivet used within the main wiring harness assembly to secure harness routing and retain protective coverings to body mounting points. Maintains st...

Spare Wheel Carrier Spacer in the rear-mounted spare wheel carrier assembly. This spacer fits within the spare wheel carrier mounting to maintain ...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Needle Roller Bearing for the manual gearbox mainshaft. The bearing carries a constant-mesh mainshaft gear, letting it spin freely on the mainshaf...

Camshaft Bearing Set for the Rover V8 petrol engine. This set provides the bearing surfaces on which the camshaft journals run within the cylinder...

Camshaft Bearing Set for the Rover V8 petrol engine. This set provides the bearing surfaces on which the camshaft journals run within the cylinder...

Seat Belt Stowage Clip from the rear seat belt assembly. It retains the seat belt webbing in a stowed position when the belt is not in use, holdin...

A/C Receiver Dryer sits on the high-pressure side of the R134a air conditioning circuit, between the condenser and the expansion valve. It stores l...

Relay (yellow) fitted in the under-bonnet fuse and relay box of the vehicle's electrical system. The relay uses a low-current control signal to sw...

Anti-Roll Bar Boot Kit is a rear actuator dust boot (gaiter) for the ACE (Active Cornering Enhancement) hydraulic anti-roll bar system. The boot s...

Headlamp, Left-Hand Side - Black Surround for left-hand drive (LHD) applications. Composite front headlamp unit providing both high and low beam f...

Headlamp, Right-Hand Side - Black Surround for left-hand drive (LHD) applications. Composite front headlamp unit providing both high and low beam ...

Front Brake Caliper Slider Pin Dust Cover Kit. This kit supplies the rubber boots that protect the front brake caliper guide pins (slide pins) fro...

Bracket Fr RR ARB Strap

Steering Box Seal Kit provides the seals for servicing the input assembly of the power-assisted steering box. This kit is used during steering box...

Selector Fork for the 5-speed manual gearbox internal gear-change mechanism. The selector fork engages with the synchromesh hub sleeve to move the...

Locking Wheel Nut Set for alloy wheels, comprising four locking nuts that replace standard wheel nuts to deter wheel theft. Thread size 16 x 1.50;...

Oil Filter Adaptor for the Td5 2.5L five-cylinder turbodiesel engine. Mounts to the engine block and provides the threaded interface for the oil f...

Release Bearing Guide for the clutch assembly on TD5 engine applications with the R380 5-speed manual gearbox. The release bearing guide (also kno...

Ignition Coil Pack in the engine ignition system, generating the high-tension voltage that fires the spark plugs. Used on the distributorless V8 e...

Upper Radiator Mounting Bracket that locates and secures the top of the radiator in the cooling system. Fitted to four-cylinder TDi and Td5 applic...

O-Ring sealing the dipstick tube where it enters the cylinder block on the V8 petrol engine. Fitted around the lower end of the dipstick tube, thi...

Bracket

Bump Stop Kit A set of four extended polyurethane bump stops, 90 mm high, in yellow. Bump stops sit between the axle and the chassis and cushion th...

Cylinder Head Gasket Set for the Td5 2.5L 5-cylinder turbo diesel, supplying the ancillary seals and gaskets used around the cylinder head when it ...