Land Rover Discovery 2 Parts

Steering Box - With Drop Arm - Right-Hand Drive for the Discovery 2 power steering circuit. This Adwest steering box assembly includes the integra...

Wiper Clip A retaining clip within the windscreen wiper assembly that secures the wiper blade to the wiper arm, holding the blade in place on the arm.

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Dial Illumination Bulb for the climate control panel, providing backlighting for the heating and ventilation controls. It seats behind the switch ...

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...

Caliper

Mud Flaps shield the bodywork and following traffic from the road spray, mud and stones thrown up by the wheels. Supplied as the right-hand pair f...

Weatherstrip - sealing strip for the rear tailgate end door glass assembly. This weatherstrip forms the perimeter seal between the rear window gla...

Wastegate Modulator for the turbocharger boost control system. This electro-pneumatic solenoid valve is controlled by the engine ECU and regulates...

Stop/Tail Bulb - 12V 21W - Twin Pack (trade reference 380). This pack contains two BAY15d dual-filament bayonet bulbs rated 12V 5/21W, suitable fo...

Cylinder Head Bolt securing the cylinder head to the cylinder block and clamping the head gasket joint. It maintains the clamping force that seals...

Windscreen Washer Jet A heated twin-nozzle washer jet that directs washer fluid onto the windscreen. It seats into the scuttle or bonnet panel and ...

Bolt Secures the radius arm to the axle bracket within the radius arms & links assembly. Installed through the radius arm bush and axle mounti...

Side Runner - Discovery 2

Low Ratio Detection Switch - the transfer box range-detection switch, mounted on the front housing of the transfer box. It senses whether the tran...

Snorkel - a raised air intake that relocates the engine's air inlet from the standard wing position up to roof height, drawing air from a higher, c...

Land Rover Oval Name Badge - Plastic - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground, moulded in ...

Pin - Split

Fuel Injector for the EFI V8 petrol engine, part of the multi-point electronic fuel injection system. The injector is an electrically-operated sol...

Auxiliary Drive Belt for the front-end accessory drive system, transmitting drive from the crankshaft pulley to the alternator and other engine anc...

Drive Belt - the auxiliary accessory drive belt for the V8 petrol engine in the configuration without air conditioning. It runs from the crankshaf...

Differential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...

Fuel Tank Locking Ring for the fuel pump and sender unit assembly. This ring secures the fuel pump and sender unit in the top of the fuel tank, pr...

Stepper Motor for the V8 EFI petrol engine, part of the idle air control system on the intake plenum. Acts as the idle air control valve, metering...

Wheel Arch Kit is a set of 75 mm extended wheel arch extensions that give coverage for wider tyres and wheel spacers. The 75 mm profile clears tyr...

Taper Roller Bearing for the front output shaft of the LT230 transfer box. Installed within the LT230 transfer case differential lock and output s...

Timing Chain Tensioner for the Td5 2.5L 5-cylinder turbo diesel, part of the timing chain drive assembly at the front of the engine. The tensioner...

Silicone Turbo Hose Kit - a four-piece set of silicone hoses that carry pressurised charge air through the turbocharger and intercooler circuit on ...

ABS Sensor - Front for the wheel speed sensing circuit on the front axle. This is the short-type sensor, terminating directly in a connector. The ...

Front Cover Gasket sealing the engine front cover to the cylinder block on the V8 EFI petrol engine. The gasket forms the joint between the timing...

Brake Caliper for the rear braking assembly, mounted on the left-hand side. The caliper houses the piston and hydraulic fluid inlet, converting pr...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

HT Ignition Lead - No.7 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...

Clutch Plate

Gasket - Cover

Nyloc Nut - M16 flanged self-locking nut used at suspension link fastenings. The integral flange spreads the clamp load across the joint face and ...

Bow Shackle Bow-shaped recovery shackle with a threaded pin, used to connect a recovery strap or rope to a recovery point on a winch bumper. The w...

Coolant Hose connecting the radiator to the expansion tank. Part of the engine cooling circuit, this hose links the radiator to the coolant expans...

Turbo Hose for the Td5 2.5L 5-cylinder turbo diesel induction system. Forms part of the air cleaner assembly, ducting filtered intake air from the...

Steering & Sump Guard - underbody skid plate. This guard fits beneath the front of the vehicle to shield the steering linkage and the engine s...

LED Side Repeater is an amber side repeater lamp within the exterior signalling circuit, mounted in the front wing aperture. Each lamp provides la...