Land Rover Discovery 2 Parts

Flanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...

Exhaust Manifold Gasket for the 4.0L and 4.6L EFi V8 petrol engine. This twin-port gasket seals the exhaust manifold-to-cylinder head joint at two...

Transfer Box Output Flange Oil Seal is a radial shaft seal fitted at the output flange of the LT230 transfer box, sealing between the rotating outp...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Gear Knob - gear lever knob for the R380 5-speed manual gearbox. Threads onto the gearchange lever, forming the driver's hand grip and gear-select...

Clutch Fork Clip secures the clutch arm rod to the release fork inside the gearbox bellhousing on LT77, LT85, and R380 5-speed manual gearboxes. T...

Nyloc Nut - M16 flanged self-locking nut used at suspension link fastenings. The integral flange spreads the clamp load across the joint face and ...

Joint washer

Brake Disc Fixing Screw that secures the brake disc to the wheel hub. The screw locates and retains the disc against the hub face during assembly,...

Nut - M6 is a plain M6 hexagonal nut used as a general-purpose threaded fastener throughout the chassis, body and mechanical assemblies. It tighte...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Speedo drive oil seal LT230

Slipper pad

Coolant - Blue RTU pre-mixed engine coolant and antifreeze for older Land Rover models. Ready to use straight from the container - no dilution req...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Interior Lamp Bulb is a 239-type festoon bulb rated 12V 5W with a C11 (SV8.5) double-ended cap, used in the interior lighting circuit. The bulb se...

Oil Pressure Switch for the V8 petrol engine, forming part of the engine oil pressure warning circuit within the lubrication system. The switch th...

Lower Ball Joint - Front Hub for the front axle steering knuckle (swivel housing) assembly. The knuckle pivots on an upper and a lower ball joint;...

Hydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...

Inlet Manifold Seal sealing the inlet manifold to the cylinder block valley on the V8 petrol engine. This formed seal closes the manifold valley j...

Panhard Rod Bush from the front suspension's lateral location linkage. The Panhard rod controls sideways movement of the axle relative to the body...

Coolant Expansion Tank Cap rated at 1.4 bar, fitted to the expansion (header) tank of the engine cooling system. The cap seals the expansion tank ...

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

Grommet

This camshaft sprocket is designed for Land Rover V8 engines, providing precise timing and reliable performance.

Fuel Tank Locking Ring for the fuel pump and sender unit assembly. This ring secures the fuel pump and sender unit in the top of the fuel tank, pr...

Handbrake Shoe Set for the transmission handbrake. Part of the transfer-box-mounted drum parking brake. The shoes expand against the inside of the...

Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...

Mirror Adapter for the exterior door mirror assembly. This adaptor forms the interface between the mirror glass and the mirror body, locating the ...

Brake Caliper for the rear braking assembly, mounted on the right-hand side. The caliper houses the piston and hydraulic fluid inlet, converting p...

Propshaft Bolt Kit - Rear is a driveline fixing set for securing the rear propeller shaft at its flange connections. The kit provides the correct-...

Flange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Brake Caliper for the rear braking assembly, mounted on the left-hand side. The caliper houses the piston and hydraulic fluid inlet, converting pr...

Capless Wedge Bulb, 12V 1.2W, for instrument, facia, clock and cigar-lighter illumination. The glass wedge base pushes directly into the panel hol...

Fuel Pipe Clip securing fuel pipe within the fuel delivery system. The clip retains and locates the fuel line along its routing, holding it agains...

Air spring clip P38, D2

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Nut - M24 x 1.5mm is a hexagonal fixing nut with an M24 fine-pitch thread (1.5mm pitch). The 1.5mm fine pitch gives more precise clamping and grea...

Lower Ball Joint - Front Hub for the front axle steering knuckle (swivel housing) assembly. The knuckle pivots on an upper and a lower ball joint;...

Front Cover Gasket sealing the engine front cover to the cylinder block on the V8 EFI petrol engine. The gasket forms the joint between the timing...

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Plain Washer for M10 fasteners. A flat washer fitted under a bolt head or nut to distribute the clamping load across the joint face, spread bearin...

Locking Wheel Nut Cap for the wheel mounting assembly. It is a push-on cover that fits over the wheel nut to conceal and protect it, keeping out ro...

tank expansion, WITHOUT CAP!

Grease Nipple is a long-thread lubrication fitting with a UNF thread form, used to deliver grease into propshaft universal joints and sliding splin...