Land Rover Discovery 2 Parts

Oil Filter for Land Rover petrol and diesel engines, part of the engine lubrication circuit. This screw-on canister filter threads onto the filter...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Fir Tree Fastener push-in fixing in grey, used to retain headlining, roof trim and similar interior and exterior trim panels. The tapered fir-tree...

Jubilee Clip - 21-44mm is a worm-drive hose clip with a 21-44mm clamping range. The band is tightened by a captive worm screw to clamp small- to m...

Level plug R380

O-ring

Plenum to Water Jacket Gasket seals the joint between the plenum chamber and the water-jacketed intake manifold in the Rover V8 EFI induction syste...

Bolt - a hexagonal-head bolt with a 5/16" UNC (Unified Coarse) imperial thread and a 3/4" length. Used as an engine-assembly fixing, including cams...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Locking Wheel Nut Key – Code A. Removal key for code-A locking wheel nuts. The key code is stamped on the original key and cannot be derived from t...

Engine Stud for the Rover V8 petrol engine, measuring 5/16" x 2-1/8" with a UNC/UNF dual thread form. The coarse UNC end threads into the engine c...

Interior Trim Fixing Clip used within body and interior trim assemblies. This clip secures trim panels, insulation sections, ducting, and fascia c...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Land Rover Oval Name Badge - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground. Fitted to the front ...

Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...

Clevis pin

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Camshaft Bearing Set for the Rover V8 petrol engine. This set provides the bearing surfaces on which the camshaft journals run within the cylinder...

Locking Wheel Nut Key - Code F for removing locking wheel nuts with the Code F drive profile, fitted to alloy wheels across the Defender, Discovery...

Hex Flange Nut - a flanged hexagonal nut used as a general threaded fastener across multiple vehicle assemblies. The integral flange spreads the c...

Fixing Screw used in the flywheel, drive plate and clutch assembly. It is one of the threaded fasteners securing the flywheel or automatic drive p...

Dowel used for the precise location and alignment of the front cover to the cylinder block on Rover V8 engines. These dowels ensure the front cove...

Brake Caliper Guide Pin Set for the sliding (floating) disc brake caliper assembly. The guide pins locate the caliper to its mounting bracket and a...

Caliper Repair Kit - Front - Axle Set

Key Wheel Nut

Hexagonal Screw - sump pan retaining screw for the ZF four-speed automatic transmission. The screw passes through one of the pressed retaining pla...

Corner Fixing Plate - pressed retaining plate for the automatic transmission sump pan, corner position. The sump pan on the ZF four-speed automati...

Inlet Manifold Insert - press-in insert that forms the vacuum take-off union in the upper inlet manifold. The insert is pressed into a machined bo...

Flanged Hex Bolt securing the lower inlet manifold on the V8 EFI petrol engine. The integral flange under the head spreads the clamping load acros...

Oil Feed Ring - mainshaft oil feed ring for the R380 five-speed manual gearbox. Located on the gearbox mainshaft, it channels lubricating oil to t...

Kit - Caliper Brake Pad

Throttle body heater plate for the 4.0L and 4.6L EFi Rover V8 petrol engine, fitted to the underside of the throttle body. The plate carries engin...

Key - Mainshaft

Handbrake Shoe Kit - the retention (hold-down) hardware for the transmission handbrake, which acts on the LT230 transfer box rather than at the roa...

Lamp

Crankshaft Pulley - for the 4.0L and 4.6L V8 EFI petrol engine. Mounts to the nose of the crankshaft at the front of the engine and drives the acc...