Land Rover Discovery 2 Parts

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Special Bolt for the front suspension radius arm. This M16 bolt secures the radius arm at its mounting, locating the arm against the chassis and a...

Automatic Transmission Oil Screen for the ZF 4-speed automatic transmission, fitted within the transmission oil sump. The screen filters the autom...

Heater Hose - inlet pipe from the cylinder head to the heater matrix, Td5 2.5L 5-Cylinder Turbo Diesel. Carries hot engine coolant from the cylind...

Oil Seal Collar for the R380 manual gearbox. The collar fits over the output shaft and provides the hardened running surface against which the gea...

Rear Bumper Trim Retainer Clip for the Discovery 2 (L318). This plastic retainer clip secures the rear bumper finisher trim at the end-cap section...

Ball Steel Bearing

Plain Washer - a flat load-spreading washer used at the body-to-chassis mount fixings. Fitted under the bolt head or nut, it distributes clamping ...

Dial Illumination Bulb - the backlight bulb and bulbholder assembly for the LCD climate control panel, part of the heating and ventilation controls...

DIFFERENTIAL - ASSEMBLY - FRONT AXLE - 24 SPLINE - 4 BOLT FLANGE - D2

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...

Side Indicator is a wing-mounted side repeater lamp in the vehicle's direction-indicator circuit, supplied as a pair. Each unit uses LED elements ...

Automatic Gearbox Sump Plug - the threaded plug that seals the drain point on the ZF automatic transmission oil pan. Removed to drain the transmis...

Steering Damper mounts in the front steering linkage to absorb kickback and reduce shimmy transmitted from the front axle to the steering wheel. T...

Rear Shock Absorber damps the rear suspension, controlling spring oscillation and wheel movement so the tyre stays in contact with the road and the...

Stud

Driveshaft Gaiter Kit is a replacement kit for the outer constant velocity joint gaiter on the front driveshaft. The gaiter protects the CV joint ...

Drive Shaft - Front - LH (left-hand) for the front axle of the Discovery 2. Complete halfshaft assembly including the CV (constant velocity) joint...

Front Wheel Hub and Bearing Assembly is the pre-assembled hub unit at the front axle, combining the wheel hub, its bearing and the ABS wheel speed ...

Roof Access Ladder provides access to the roof and roof rack. It mounts to the rear bodywork and gives a secure step up for loading, unloading and...

Front Brake Caliper Repair Kit for front calipers used with vented discs. The kit supplies the piston seals needed to overhaul the front calipers....

Front Brake Caliper Repair Kit for front calipers used with vented discs. The kit supplies the piston seals needed to overhaul the front calipers....

Drag Link Ball Joint (Short) is a steering linkage joint fitted at the short end of the drag link, within the steering track-rod circuit. It forms...

Brake Pipe Clip - Rear secures the rear brake pipes on the Discovery 2, holding the hydraulic lines in place along the chassis. The clip prevents ...

Bolt, M10 x 30mm, used to secure the upper mounting bracket of the suspension damper. It fastens the shock absorber upper mount bracket at the fro...

Filter valve assy

Road Coil Spring - Front for the Discovery 2 front suspension. This coil spring seats in the front spring pan on the axle beam and bears against t...

Steering damper Discovery 2

LHD Steering Drag Link Lemforder / Moog - Discovery 2

Flywheel Assembly for the 2.5L Td5 five-cylinder turbo diesel engine, mounted between the engine and the manual gearbox. Bolted to the rear of the...

Cooler Oil

Manifold Absolute Pressure (MAP) Sensor, part of the engine management system. The MAP sensor measures the absolute pressure inside the intake man...

Channel glass front door. - Discovery1 from (VIN) MA137190 onwards, - RRclassic 4-door from (VIN) MA659911 onwards. Also fits Discovery2 front LH ...

Braided Brake Hose Kit, extended by 150mm, covering the flexible sections of the hydraulic brake circuit between the chassis-mounted brake pipes an...

Steel hex full nut, M8 x 1.25 thread, catalogued for the clutch and dual-mass flywheel assembly on the Td5 2.5L 5-cylinder turbo diesel engine. Th...

Nyloc Flanged Nut - M8 flanged nut with a nylon insert, used on front suspension fixings. The nylon collar deforms around the bolt thread as the n...

Cam Follower - a roller-type tappet operating in the engine valve train, between the camshaft and the pushrod. It rides on the camshaft lobe and t...

Banjo Bolt for the turbocharger oil feed pipe on the Td5 engine. This M12 x 1.0mm thread banjo bolt clamps the hollow banjo fitting of the oil sup...

Blade Fuse - 25A for Land Rover electrical systems. This 25A blade fuse protects individual circuits in the vehicle fuse box from overcurrent damage.

Big End Bearing Set — connecting-rod (big-end) bearing shells for the V8 engine bottom end. The shells sit between the connecting-rod big-end bore...

Nyloc Nut - M16 for use in the front axle steering knuckle assembly. This M16 self-locking nut uses a nylon insert to provide prevailing-torque re...

Crown wheel and pinion set with a 4.1:1 final drive ratio for the rear differential, long nose differential configuration. The crown wheel and pin...

Self-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...

Exhaust Downpipe with Catalytic Converter - the front section of the exhaust system on V8 petrol applications. It bolts to the exhaust manifold ou...

Rivet used within the main wiring harness assembly to secure harness routing and retain protective coverings to body mounting points. Maintains st...

Spare Wheel Carrier Spacer in the rear-mounted spare wheel carrier assembly. This spacer fits within the spare wheel carrier mounting to maintain ...