Genuine Land Rover Parts

Nut for the diesel fuel injection pump and timing gear. Secures the drive gear to the high-pressure fuel injection pump on the 2.7L Lion V6 diesel...

Adjusting Screw for the Td5 2.5L five-cylinder turbo diesel engine rocker assembly. Sets the clearance at the rocker where it acts on the valve an...

Front Camshaft Oil Seal for the Td5 2.5L 5-Cylinder Turbo Diesel engine, fitted at the timing end of the camshaft within the cylinder head. Seated...

Heat Shield - Engine Mount for the Puma diesel engine mounting assembly. This shield mounts over the engine mount rubber to protect it from heat a...

A/C Compressor O-Ring seals a refrigerant line union at the air conditioning compressor. The O-ring is clamped between the pipe end fitting and th...

Clip retains the heater and air-conditioning control cable within the HVAC control assembly, holding the cable on its correct routing.

Low Ratio Detection Switch - the transfer box range-detection switch, mounted on the front housing of the transfer box. It senses whether the tran...

Clutch Release Lever Pivot provides the fulcrum for the clutch release lever. The release lever pivots on this point to transfer slave-cylinder mo...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Turbocharger Adaptor Pipe in the induction system of the 2.5L 200 TDi and 300 TDi turbo diesel engines. It forms the connecting pipe between the t...

Oil Seal Housing Gasket for the 300 TDi engine, sealing the rear crankshaft oil seal housing to the rear face of the cylinder block. The gasket fo...

Crankshaft Oil Seal - Front seals the nose of the crankshaft where it passes through the timing cover on the Td5 2.5L 5-cylinder turbo diesel engin...

Cylinder Head Bolt securing the cylinder head to the cylinder block and clamping the head gasket joint. It maintains the clamping force that seals...

Injector Sealing Washer seals each fuel injector into the cylinder head within the diesel fuel injection system, for 200 TDi and 300 TDi turbo-dies...

Windscreen Washer Reservoir

Washer Reservoir The container that stores washer fluid for the windscreen and rear tailgate window wash systems. The dual-wash reservoir supplies ...

ROVER Lettering Emblem - silver, 35 cm - for Defender (2007-2016). This is the adhesive silver lettering strip that spells out "ROVER" on the exte...

Emblem - LAND - Silver - 28cm is the "LAND" lettering badge that forms part of the bonnet exterior script. The silver badge measures 28 cm in leng...

Lockset-Complete Vehicle

Run Assembly - Glass

Glass Run Channel for the rear quarter window. The run channel lines the window aperture and guides and locates the rear quarter glass, sealing it...

Rivet used to secure exterior body panels and mouldings, including front wing and body-moulding assemblies. Installed through the panel to retain ...

Decal

Warning Label Decal - an adhesive warning label applied to the bodywork. It reproduces one of the factory information and caution labels, restorin...

High-Mounted Stop Lamp Stud is a mounting stud for the high-level stop lamp. It secures the high-level (centre) stop lamp to its mounting point on...

Mounting Bracket - cab body panel fixing bracket. Supports and locates the cab body panel, forming part of the body panel fixing arrangement.

Bonnet Release Cable connects the cabin-mounted release lever to the bonnet latch as part of the bonnet locking mechanism. Pulling the interior le...

Spire Nut (U-type spire fastener) for trim and panel fixings. Spring-steel push-on nut that clips over a panel edge or stud to provide a captive f...

Vent Assembly Knob for the dashboard air vent control on models without air conditioning. The knob fits onto the vent control lever and provides t...

Body Washer, 22mm outer diameter, 6.5mm inner diameter. A flat washer that spreads the clamping load of a fixing across the mounting surface, prot...

Speedometer for the instrument cluster, displaying road speed on non-EFI applications. It mounts in the dashboard instrument panel and is driven b...

36 Spline Steering Wheel with a black leather rim. It mounts on the 36 spline upper steering column shaft and is retained by the column nut. The s...

Front Wheelarch is a body panel that forms the wheel housing around the front wheel on the right-hand (RH) side. It encloses the upper and rear fa...

Filler - Rear Quarter Panel

Cable Clip for securing and routing cables and wiring to body and chassis structures.

Rear Fog Lamp Assembly for the Defender, incorporating the direction indicator and reverse light functions within the same housing unit. Replaces a...

Shim door GENUINE - door striker plate 1958 - 1984 - side hinged tailgate

Restrictor - flat 20 mm plain washer used in the suspension link mountings of the coil-sprung live-axle chassis. It is fitted at the radius arm mo...

Output Shaft - MT82 6-Speed Manual Gearbox. The output shaft is located at the rear of the MT82 transmission housing and transmits rotational driv...

Sunroof Seal

Manifold Stud - M8 x 36 mm - for the Td5 2.5L 5-cylinder turbo diesel engine. The stud threads into the cylinder head to locate the manifold flang...