Genuine Land Rover Parts

Wheel Centre Cap - a black alloy-wheel centre cap carrying the Land Rover oval in green and silver. It presses into the centre bore of an alloy wh...

24v dsl long belt

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Bolt - M8 x 50 - Torx is an M8 threaded fastener, 50 mm long, with a Torx drive head. It is used as a general-purpose fixing across a range of bod...

Key Fob Cover Kit provides a replacement outer cover for the remote key fob, renewing a housing that has become worn, cracked or faded. It restore...

Wheel Centre Cap - set of four alloy wheel centre caps in Titan Silver. The centre cap clips into the hub bore of an alloy wheel, covering the hub...

Magnetic Oil Drain Plug for the engine oil sump on the 2.0L Ingenium (AJ200/AJ20) four-cylinder petrol and diesel engines. The plug seals the drai...

Coolant Outlet Connection is part of the engine cooling circuit, forming the sealed outlet junction where coolant leaves the engine on its way to t...

Oil Separator for the crankcase ventilation circuit of the 3.0L V6 Diesel engine. Mounted within the crankcase emission control system, the separa...

Coolant Hose forms part of the heater line within the engine cooling system, routing coolant between the engine and the heater matrix. Supplied co...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Wheel Centre Cover fits into the central hub bore of an alloy wheel, concealing the hub and wheel-mounting hardware behind a finished cap that clip...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Air Filter element for the engine air cleaner assembly. The filter sits inside the air cleaner housing and cleans the intake air before it passes ...

Catalyst Gasket for the exhaust system of the 2.0L 16V Ti-VCT four-cylinder petrol engine. This gasket seals the joint at the catalytic converter ...

Oil Pump for the 2.7L and 3.0L V6 diesel (Lion) engine, operating within the lubrication circuit as part of the oil pump and sump assembly. Driven...

Oil Separator Pipe for the 3.0L V6 diesel engine, forming part of the crankcase emission control (crankcase ventilation) system. It carries blow-b...

Oil Filter - the engine oil filter element for the 3.0L V6 turbo diesel (TD6) engine. Fitted in the engine lubrication circuit, the filter traps m...

Clip retaining the top of the rear air spring within the rear spring and shock absorber assembly. The clip locates and secures the air spring at i...

Leak-Off Tube - Injection Pump

Exhaust Gas Temperature Sensor measures exhaust gas temperature at the front of the diesel particulate filter, in the upstream section of the after...

Front Driveshaft, Left-Hand transmits drive from the front differential to the left front wheel hub within the front axle assembly. Constant-veloc...

Oil Pump Chain Tensioner for the 2.0L turbocharged direct-injection petrol engine. Maintains correct tension on the oil pump drive chain, taking u...

Crankshaft Timing Gear for the 2.0L 16V TiVCT turbocharged petrol engine (Si4 240PS and Gen2). It mounts on the nose of the crankshaft and drives t...

Oil Cooler Assembly is the combined engine oil cooler and filter assembly within the engine lubrication and cooling circuit. It passes hot engine ...

Timing Chain for the 2.0L 16V TiVCT turbocharged petrol engine (Si4 240PS and Gen2). It forms part of the engine's timing drive, running between th...

Oil Pump Chain is the drive chain for the engine oil pump on the 2.0L 16V turbocharged petrol engine. It transmits drive from the crankshaft to th...

Cable Connector is a four-way electrical connector body used in the vehicle wiring harnesses. It joins a harness branch to its mating half, retain...

Asy Lamp

Exhaust Gasket sealing a flanged joint in the exhaust system on Land Rover and Range Rover models fitted with the 2.7L TDV6, 3.0D V6, 2.2D, and 4.4...

Side step insulator - a moulded pad that sits between the side step mounting bracket and the vehicle body, within the deployable side step mounting...

Washer - Sealing

Bolt

Hex Nut is an M6 flange nut with a 10mm hexagonal drive. It retains wheel arch liner and splashguard panels on their mounting studs. The integral ...

Collet - Anti-Roll Bar Pipe - retaining collet used in the pipe connections of the Active Cornering Enhancement (ACE) anti-roll bar system. The co...

Rear brake disc, 365mm diameter, forming part of the rear brake disc and caliper assembly. The disc bolts to the rear hub flange and provides the ...

Front Brake Pad Kit - friction pad set for the front disc brake assembly, for the 380 mm front disc and size 20 caliper configuration. The pads lo...

Front Brake Caliper Attachment Kit - the caliper fitting hardware for the front disc brake assembly. The kit contains the brake pad clips and the ...

Cable Connector - an electrical connector used in the vehicle wiring harness. The connector forms the termination between a harness cable and its ...

Door Handle Gasket - sealing gasket for the exterior door handle and lock assembly, part of the door closures group. It sits between the handle es...

Grille - Dirty Air Duct for the engine air intake and filtration assembly. Fits over the mouth of the dirty air duct on the front fender support, ...

Dirty Air Duct Guide for the engine air intake system. The guide locates and supports the dirty air duct, the unfiltered-air inlet duct that carri...

Injector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...

Head Gasket for the right-hand cylinder bank of the 5.0L V8 AJ133 petrol engine. It seals the cylinder head to the engine block, containing combust...