Genuine Land Rover Parts

D3S xenon headlamp bulb, supplied with its igniter, for headlamp units originally built as bi-xenon or adaptive xenon assemblies. D3S is a mercury...

Exhaust Clamp - 60mm exhaust joint clamp for the front section of the exhaust system, securing the downpipe to the centre silencer section. Clamps...

Bumper Retainer Nut - a push-in retaining nut used in the front bumper, radiator grille and rear bumper assemblies. The retainer clips into a pres...

Trim Clip that secures interior and exterior trim panels, door finishers and mouldings to the body. The clip locates in a pre-formed panel apertur...

Bolt - M8 x 75mm secures the lower timing gear on the V6 diesel engine. It is a fastener within the timing gear drive assembly. Thread size M8, le...

Oil Sump Gasket seals the oil pan (sump) to the cylinder block on the V6 diesel engine. It maintains an oil-tight joint at the base of the engine,...

Bolt for the exhaust system front section. This fastener secures the flanged joint between the exhaust manifold and the front pipe section, holdin...

Brake Disc & Caliper Bolt - a fixing bolt for the brake disc and caliper assembly. It is used at both the front and rear brake disc and calipe...

Bolt

Hex Nut - M12 - a standard M12 hexagonal nut used as a general-purpose fastener across the vehicle. The six-sided form is tightened with a standar...

Flanged Nyloc Nut, M10, a multi-purpose locking fastener used across the chassis and suspension. The nylon insert resists loosening under vibratio...

Glove Box Door Damper. Controls the rate at which the glove box lid opens, providing a smooth, damped movement within the facia glove box assembly.

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Front Brake Pad Set - the friction pads for the front-axle disc brakes. The pads sit in the caliper and are clamped against the brake disc by the c...

Gasket - Oil Tube

Exhaust Manifold Stud for TDV6 2.7 and 3.0 and TDV8 3.6 diesel engines, used to fasten the exhaust manifold to the cylinder head. On 2.7 TDV6 engi...

Oil Pump Seal for the V6 diesel engine oil pump assembly, part of the engine lubrication circuit. It seals the oil pump interface to prevent oil l...

Oil Separator Seal - sealing gasket for the oil separator in the crankcase ventilation system of the 2.7 and 3.0 litre V6 diesel engines. The oil ...

Oil Tube Gasket seals the turbocharger oil drain (return) pipe where it joins the engine, within the turbocharger lubrication circuit. After lubri...

Camshaft Pulley Hub mounts to the front of the right-hand (RH) cylinder bank camshaft on the 2.7L and 3.0L V6 diesel engine, forming part of the ti...

Timing Chain & Tensioner Kit - Upper

Bolt - Exhaust Manifold & EGR - a fixing bolt used in the exhaust manifold and exhaust gas recirculation (EGR) assembly of the TDV6/TDV8 diesel...

Clamp - Tube

Camshaft Seal for the TDV6 2.7L V6 diesel engine. Seals the camshaft at its exit point from the cylinder head, preventing oil leakage from the cams...

Kit - Drive Belt

Valve Stem Seal for the cylinder head valvetrain on TDV6 and TDV8 diesel engines. Fitted to both inlet and exhaust valves, the seal presses onto th...

Metering Valve for the fuel injection system of the 4.4L V8 TDV8 diesel engine. Mounted on the high-pressure fuel pump assembly, the metering valv...

Inlet Manifold Sensor for the 4.4L V8 TDV8 Diesel engine management system. This sensor monitors pressure and temperature within the intake manifo...

A/C Compressor Line Tube is a refrigerant line in the air-conditioning circuit, routing between the compressor and the condenser. It carries refri...

Fuel Rail Pressure Sensor for the 4.4L V8 TDV8 diesel engine, fitted within the high-pressure common-rail fuel injection system. The sensor monito...

Inlet Manifold - LH

Fuel Filter Element - the in-line fuel filter element on the front fuel supply lines. It removes particulate contamination from the diesel supply ...

Oil Filter - the replaceable cartridge element for the engine lubrication circuit, fitted inside the filter housing on the oil pump, cooler and fil...

Flanged Nut for use in Land Rover assembly applications. The integrated flange acts as a built-in load-spreading face, distributing clamping force ...

Screw - an M6 x 20 mm pan-head setscrew with a Torx drive, used as a general multi-application fastener. The Torx socket gives positive tool engag...

Cooling Turbo Gasket

Camshaft Screw for the cylinder head and camshaft assembly of the 3.0-litre TDV6 diesel engine. This is a manufacturer-specification retaining scr...

Relay Black 2A 4 Pin