Genuine Land Rover Parts

Brake Caliper - Rear - RH is the right-hand rear caliper of the disc brake assembly. Under hydraulic pressure from the rear brake circuit, it clam...

Rear Brake Caliper - Left-Hand is part of the rear braking assembly, mounting over the rear brake disc on the left-hand side of the vehicle. The c...

Bulb Holder - double-pole bulb holder for the rear stop and tail lamp. It carries the twin-filament stop/tail bulb and locates by bayonet fitting ...

Number Plate Lamp Lens - clear lens for the rear licence plate lamp mounted in the luggage compartment door. The lens clips into the lamp housing ...

Rear Bumper Lamp, Right-Hand Side. Lamp unit installed in the right-hand side of the rear bumper, forming part of the rear exterior lighting assemb...

Lamp Assembly-Rear

Asy Lamp

Fuel Pipe Assembly forming the vent lines of the Td5 2.5L 5-cylinder turbo diesel fuel system. The vent pipework carries fuel vapour away from the...

Exhaust Gas Temperature Sensor for the diesel exhaust aftertreatment system, fitted to vehicles equipped with a diesel particulate filter (DPF). T...

Exhaust Mounting is a moulded rubber mounting that suspends the front section of the exhaust system from the vehicle body. The rubber body links t...

Exhaust Gasket sealing a flanged joint in the exhaust system on Land Rover and Range Rover models fitted with the 2.7L TDV6, 3.0D V6, 2.2D, and 4.4...

Worm Drive Hose Clamp used in the exhaust gas recirculation (EGR) circuit of the 3.0L M57 turbo diesel engine. The clamp secures a flexible hose o...

Parking sensor bezel in black, the retaining trim ring that locates a Park Distance Control (PDC) ultrasonic sensor in its bumper aperture. The be...

Loadspace rubber mat for the rear load compartment, part of the interior protection group. The mat is tailored to the loadspace floor and protects...

Side step insulator - a moulded pad that sits between the side step mounting bracket and the vehicle body, within the deployable side step mounting...

Kit - Floor Contour Mat

Bush - Steering Column

Washer - Sealing

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Wiper Drum Adaptor - splined adaptor used in the windscreen wiper system to connect the wiper arm to the splined wiper spindle. The adaptor seats ...

Locking Wheel Nut Kit for alloy road wheels, part of the road wheel and fixings assembly. Each locking nut replaces a standard wheel nut at one pos...

Key Wheel Nut

Guide Pin for the auxiliary drive belt tensioner and front timing cover on the 2.5L six-cylinder diesel. The pin locates the tensioner assembly to...

Handbrake Operating Lever from the parking brake control assembly. The lever is the driver-operated arm that applies the transmission brake through...

Brake Pipe Clip is a retaining clip from the front brake line mounting hardware. The double form holds two rigid brake pipes side by side at a fix...

Handbrake Shoe Set for the mechanical parking brake, which operates inside its own dedicated drum and is independent of the hydraulic service brake...

Disc - Brake

Disc - Brake

Brake Disc - a front vented brake disc, the rotating friction surface the caliper pads clamp against to slow the vehicle. The internal vanes draw ...

Bolt

Hex Nut is an M6 flange nut with a 10mm hexagonal drive. It retains wheel arch liner and splashguard panels on their mounting studs. The integral ...

Seal

Collet - Anti-Roll Bar Pipe - retaining collet used in the pipe connections of the Active Cornering Enhancement (ACE) anti-roll bar system. The co...

Anti Roll Bar Bush locates the anti-roll bar in its chassis mounting bracket, providing a resilient rubber interface between the bar and the subfra...

Upper Front Suspension Arm Ball Joint The upper ball joint forms the top pivot between the front upper suspension arm and the wheel knuckle, holdi...

Plastic Rivet from the engine cooling assembly, used to retain the radiator and the coolant overflow container. The rivet is a push-fit fastener: ...

Flywheel Bolt with hex head, securing the flywheel to the crankshaft rear flange on the 2.7L V6 Lion turbo diesel fitted with the ZF S6-53 six-spee...

Split Pin used throughout the handbrake and gearchange linkages. The pin passes through a clevis pin or castle nut and its legs are spread on asse...

Drive Belt Bracket and Bearing for the auxiliary (accessory) drive belt system. The bracket mounts to the engine and locates a pulley within the a...

Auxiliary Drive Belt for the 2.7L TDV6 diesel engine on vehicles without an active roll stabiliser, 2092mm. This ribbed belt transmits drive from ...

Radiator Fan Shroud - the lower section of the cooling fan housing, fitted behind the radiator around the bottom of the engine-driven cooling fan. ...

Radiator Fan Cowl - the upper section of the cooling fan shroud in the engine cooling pack, sitting between the top of the radiator and the engine-...

Coolant Pump Cover for the 2.0L four-cylinder TCIE diesel engine, part of the engine cooling circuit. The cover closes the coolant pump housing an...

Coolant Hose - the top radiator hose in the Td5 2.5L 5-cylinder turbo diesel engine cooling system. This hose forms part of the upper coolant circ...

Coolant Hose - Radiator Top - upper radiator hose in the engine cooling circuit of the M47 2.0L 16-valve Td4 turbo diesel, automatic transmission a...