Genuine Land Rover Parts

Radius Arm Bush - Front is the flexible mounting bush at the front radius arm-to-chassis location. The radius arm locates the front axle longitudi...

HT Ignition Lead - V8 - No.8 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition out...

HT Ignition Lead - No.7 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

HT Ignition Lead - No.6 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

HT Ignition Lead - No.5 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

HT Ignition Lead - No.4 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

HT Ignition Lead - No.2 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

O-Ring - Fuel Injector - Diesel - sealing ring in the fuel injector and pipe assembly on diesel engines. The ring seals the injector joint against...

Grille Badge is an exterior badge mounted on the front grille. It fits to the grille panel to display the marque at the front of the vehicle.

Decal is an exterior body decal applied to the rear of the vehicle. It carries the Land Rover name in silver lettering on a black background, and ...

Spare Wheel Clamp Plate - 16mm

Door Lock Escutcheon in black, part of the door casing and lock trim. The escutcheon is the moulded finisher that fits over the aperture in the do...

Snap-sac trim clip - the push-in plastic fastener that secures interior trim panels to their supporting structure. The clip passes through a hole ...

Hinge Packer Shim for the door hinge assembly. Fitted between the hinge and its mounting face to set door alignment. Adding or removing shims adju...

Bonnet Safety Catch Hook is the secondary latch that engages after the primary bonnet release is operated. Part of the bonnet locking mechanism, i...

Exterior mirror head for the left-hand side, with flat glass. The complete head assembly - housing, backing plate and glass - that mounts to the ar...

Exterior mirror head for the right-hand side, with flat glass. The complete head assembly - housing, backing plate and glass - that mounts to the a...

Rear Door Lock Assembly - LH - complete latch and lock mechanism for the left-hand rear door, operating within the door locks and handles assembly ...

Exterior Mirror with convex glass and a black finish, supplied as a complete door-mounted mirror assembly. The convex glass gives a wider rearward...

Door Seal Retainer - Rear End for the rear door seal assembly. This retainer locates and secures the door weatherstrip in its channel along the re...

Switch - Fuel Shut-Off

Fuel Shut-Off Switch for the Td5 diesel fuel system - an inertia-operated safety switch wired into the fuel pump supply circuit. In the event of a...

Throttle body heater plate for the 4.0L and 4.6L EFi Rover V8 petrol engine, fitted to the underside of the throttle body. The plate carries engin...

Fuel Supply Tube - supply tube in the fuel delivery circuit of the 4.4 AJ-V8 petrol engine. The tube carries pressurised fuel from the feed line t...

Fuel Injector Supply Tube - supply tube in the fuel delivery circuit of the 4.4 AJ-V8 petrol engine. The tube carries pressurised fuel from the fe...

Inlet Manifold Insert - press-in insert that forms the vacuum take-off union in the upper inlet manifold. The insert is pressed into a machined bo...

Stud, a double-ended threaded stud in the exhaust and turbocharger assembly, threaded M10 x 20 mm at one end and M10 x 13 mm at the other. It prov...

Flanged Hex Bolt securing the lower inlet manifold on the V8 EFI petrol engine. The integral flange under the head spreads the clamping load acros...

Crankshaft Pulley Bolt for the Td5 2.5L five-cylinder turbo diesel engine, securing the crankshaft pulley and torsional vibration damper to the nos...

Cam Cover Bolt for the Td5 2.5L 5-cylinder turbo diesel engine, securing the camshaft cover to the cylinder head. This is the flanged-head bolt th...

Camshaft Cover Bush for the 4.4L M62 B44 V8 petrol engine, fitted at the camshaft cover fixing points on the cylinder head cover. Each bush seats ...

Heat Shield Bracket for the exhaust manifold and turbocharger heat shield on the Duratorq TDCi (Puma) diesel engine. The bracket bolts to the exha...

Gasket - Cover

Thermostat Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the coolant outlet elbow to the thermostat housing. It forms the coolan...

Sump Gasket for the Rover V8 4.0 and 4.6 petrol engine, sealing the oil sump to the underside of the cylinder block. This is the one-piece rubber-...

Rocker Cover Gasket for the Rover V8 petrol engine, sealing the rocker (valve) cover to the cylinder head. The gasket seats between the cover flan...

Cylinder Head Gasket, 1.20mm thickness, two-hole identification, for the 2.0L L-Series 8V TCIE direct injection diesel engine. The gasket seals th...

Handbook - English Edition