Genuine Land Rover Parts

Heater Valve for the cabin heating circuit on Defender Puma diesel models from 2007 onwards. This valve regulates the flow of engine coolant to th...

Exhaust Heat Shield - a formed metal shield fitted in the exhaust system area of the underbody. The shield sits between the exhaust and the adjace...

Pollen Filter for the heating and ventilation system. It installs in the cabin air intake, upstream of the blower motor, trapping dust, pollen and ...

O-Ring - sealing ring used inside the heating and air conditioning unit, sealing the joints between the internal components of the assembly. Rubbe...

Coolant Vent Hose - a small-bore hose in the engine cooling and cabin heater circuit of the 2.4 TDCi Puma diesel. Connected at the heater outlet, ...

Hose - Heater Water

Hose

Blower Motor Resistor Pack - speed control for the heater and air conditioning blower motor, also referred to as the air conditioning switch. The ...

Heater Blower Motor and Fan Assembly - the powered fan unit of the cabin heating, ventilation and demisting system. The electric motor drives the ...

Heater Control - the heater and air-conditioning control panel mounted in the centre of the dashboard. It carries the rotary controls for cabin te...

Fuel Filter Shield is a protective cover fitted over the fuel filter assembly. It mounts over the filter housing and shields the filter body and i...

Air Intake Plenum Extension Moulding in black, the moulded panel that sits in the scuttle area between the rear edge of the bonnet and the base of ...

A-Pillar Trim Clip A retaining clip used in the interior A-pillar trim assembly. It secures the A-pillar trim panel to the body structure alongsid...

Gear Change Lever Knob for the transfer box gear change lever. The knob fits to the top of the transfer lever and forms the hand grip used to sele...

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...

Cover - Seat Back Hinge

Seat Back Adjustment Handle - the operating handle for the front seat backrest recline mechanism, mounted on the outboard side of the seat frame. ...

Trim Clip - retaining clip for interior trim panels. Secures interior trim components such as the instrument panel, glove box and speaker surround...

Hex Nut - M12 - a standard M12 hexagonal nut used as a general-purpose fastener across the vehicle. The six-sided form is tightened with a standar...

Flanged Nyloc Nut, M10, a multi-purpose locking fastener used across the chassis and suspension. The nylon insert resists loosening under vibratio...

Flanged Nut - M10 flanged fastener. The integral flange spreads the clamping load over a wider area and resists loosening under vibration, removin...

Flange Nut, M16 for the suspension arm mountings. The integral flange spreads the clamping load over a wider bearing area and removes the need for...

Actuator

Tailgate Lock Actuator - Upper

Latch

Seal

Clutch Slave Cylinder for the hydraulic clutch release system on Defender and Discovery 2 models fitted with the R380 manual gearbox. Mounted on t...

Crown Wheel Bolt - a fastener in the differential final drive assembly of the Land Rover type axle. It secures the crown wheel (ring gear) to the ...

Selector Lever for the manual gearbox gear selection mechanism. It transmits movement from the gear lever to the selector shafts inside the gearbox...

Brake Disc Splash Shield - Front, RH, mounted behind the right-hand front brake disc. The shield sits between the stub axle / hub and the brake di...

Front Driveshaft Oil Seal located at the differential housing output in the Front Axle Assembly, sealing around the front halfshaft where it exits ...

Hub Oil Seal - Inner for the front and rear wheel hubs, seating around the stub axle. The seal runs on the stub axle to retain hub lubricant and e...

Swivel Pin Gasket seals the joint between the swivel pin housing and the axle case on the front axle. It sits at the mating face where the swivel ...

Swivel Joint Washer located within the Swivel Pin Housing Assembly, sealing the interface between the swivel housing flange and the axle beam face....

Bonnet Release Cable for the bonnet-release mechanism. It links the interior release lever to the bonnet latch: pulling the cabin lever draws the ...