Land Rover Axle & Swivel Parts

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

Swivel Housing Grease for the front axle swivel assembly, supplied as a single pre-measured one-shot sachet. The sachet delivers the correct charg...

Drive flange for the front axle drive shaft hub assembly. This component provides the splined connection between the drive shaft and the wheel hub,...

Swivel Pin Gasket seals the joint between the swivel pin housing and the axle case on the front axle. It sits at the mating face where the swivel ...

Front Stub Axle for the front hub and swivel pin housing assembly at the front axle. The stub axle passes through the swivel pin housing and provi...

Drive Flange for the front hub assembly. The drive flange bolts to the outer face of the hub and engages the splined end of the axle half shaft, t...

Lower Swivel Pin for the front axle swivel housing assembly. The lower swivel pin provides the lower pivot point for the steering knuckle, working...

Swivel Shim is a 0.75 mm selective shim from the front axle swivel pin assembly. It is fitted beneath the upper swivel pin retaining plate, where s...

Swivel Pin Housing Shim - 0.13mm (0.005") for the front axle swivel pin housing assembly. This precision shim is fitted between the swivel pin hou...

Swivel Housing Washer for the swivel pin housing drain plug, part of the front axle swivel assembly. The sealing washer fits beneath the drain plu...

Swivel Pin Housing Shim - 0.25mm (0.010") for the front axle swivel pin housing assembly. This precision shim is fitted between the swivel pin hou...

Swivel Pin Housing Shim - 0.075mm (0.003") for the front axle swivel pin housing assembly. This precision shim is fitted between the swivel pin ho...

Front axle drive flange designed to connect the drive shaft to the wheel hub assembly. The flange transmits rotational force from the half shaft ...

Rear Differential Drive Flange Kit for the Land Rover (Rover-type) rear axle. The drive flange mounts to the differential pinion and provides the ...

Swivel Ball Inner Bearing Housing for the front axle swivel assembly. It locates and supports the inner bearing within the swivel ball, maintaining...

Drive Flange for the front hub assembly. The drive flange bolts to the outer face of the hub and engages the splined end of the axle half shaft, t...

Stub Axle Washer for the front and rear hub and wheel bearing assembly. The washer locates over the stub axle and seats between the outer wheel bea...

Front Stub Axle for the front hub and swivel pin housing assembly at the front axle. The stub axle passes through the swivel pin housing and provi...

Half Shaft Shim - 0.60mm is a 0.60mm selective shim used to set the endfloat of the axle half shaft within the hub assembly. It is fitted at the d...

Front Axle Shim, 0.45mm thick. Fitted to the front axle half-shaft assembly to set the correct end-float, taking up clearance so the shaft is posit...

Lower Swivel Pin forming the lower pivot of the front axle swivel housing. The pin bolts to the underside of the swivel pin housing and carries th...

Stub axle

Swivel Housing: - Classic Defender 90/110/127/130 upto KA930455 (upto and including 1993 modelyear) (NON-ABS) Axle Code 20L, 21L, 22L, 23L, - Disco...

Half Shaft Shim - 0.90mm is a 0.90mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Half Shaft Shim - 0.75mm is a 0.75mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Trunnion

Half Shaft Shim is a 1.05mm selective shim used in the front axle drive shaft and hub assembly. It sets the endfloat of the front half shaft drive...

Front Half Shaft for the right-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant vel...

Upper Front Swivel Pin for the front axle swivel housing assembly. The upper swivel pin bolts to the top of the swivel housing and forms the upper...

Swivel Housing Kit providing a complete overhaul of the front axle swivel assembly for one side, supplied complete with the swivel housing ball. T...

Rear Stub Axle for non-ABS applications. Bolts to the rear axle case to carry the hub bearings and support the rear hub assembly. For vehicles bui...

Half Shaft Shim is a 1.50mm selective shim used in the axle drive shaft and hub assembly. It sets the endfloat of the half shaft drive member with...

Outer Shim - 1.35mm - Front Halfshaft / CV Joint This 1.35mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Shim

Front Half Shaft for the left-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant velo...

Differential Pinion Bearing Shim - 0.068 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Differential Pinion Bearing Shim - 0.066 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Differential Pinion Bearing Shim - 0.064 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Shaft 90/110 RH 31/10

Front Halfshaft - Left Hand for the early Discovery 1, transmitting drive from the front differential to the left-hand front swivel housing. The h...

Front Halfshaft - Right Hand for the early Discovery 1, transmitting drive from the front differential to the right-hand front swivel housing. The...

Differential Pinion Bearing Shim - 0.070 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Swivel kit OEM Discovery 1 & Range Rover Classic with ABS

Swivel Pin Kit - Upper for the front axle swivel pin housing assembly. The upper swivel pin forms the top pivot about which the swivel housing rota...

Drive Flange Nut - Front secures the front drive flange (driving member) to the wheel hub, as part of the front hub assembly. It retains the drivi...

Outer Shim - 1.65mm - Front Halfshaft / CV Joint This 1.65mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Upper Swivel Pin forming the upper pivot of the front axle swivel housing. The pin bolts to the top of the swivel pin housing and runs in the uppe...

Swivel Pin Housing Shim - 0.010in is a 0.010 in (0.25 mm) shim used to set the bearing preload in the front axle swivel pin housing assembly. Fitt...