Land Rover Axle & Swivel Parts

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

Swivel Housing Grease for the front axle swivel assembly, supplied as a single pre-measured one-shot sachet. The sachet delivers the correct charg...

Swivel Housing to Stub Axle Joint Washer for the front axle swivel assembly. This sealing washer fits between the swivel housing and the stub axle...

Axle Breather for the front axle housing on vehicles without a remote breather pipe assembly. This screw-in vent allows the air inside the front a...

Swivel Pin Housing Gasket for the front axle swivel assembly. This gasket seals the mating face between the chrome swivel ball housing and the fro...

Swivel Pin Lock Tab for the front swivel pin housing on Land Rover Series II, IIA, and III. Fitted to the 7/16 BSF studs that retain the swivel pi...

Lock Plate for the front axle assembly. This metal tab washer locks fastener heads in position by bending a tab against the bolt head or nut after...

Stub Axle Gasket for the rear drive shaft assembly on Land Rover Series II, IIA, and III. This gasket seals the stub axle flange at the rear axle ...

Swivel Ball Seal Retainer for the front axle swivel housing. This retaining ring clamps the swivel housing oil seal against the swivel ball, holdi...

Swivel Housing Washer for the swivel pin housing drain plug, part of the front axle swivel assembly. The sealing washer fits beneath the drain plu...

Swivel pin & bracket

Shim .003" for swivel pins

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Swivel Pin Shim for the front axle swivel housing assembly. This 0.030" shim is fitted beneath the upper swivel pin retaining plate and is used to ...

Swivel Pin Shim, 0.010" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...

Drive Flange & Mudshield Kit for the Salisbury rear axle. The drive flange bolts to the rear hub and couples the axle half-shaft to the hub, t...

Swivel Pin Shim, 0.005" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...

Drive Member - 10-Spline is the drive coupling at the outer end of the axle, forming part of the wheel hub and drive assembly. Its 10-spline inter...

Swivel Housing Kit for the front axle swivel assembly, covering one side of the axle. This is the later configuration, with the steering arm mounte...

Transfer Box Intermediate Shaft Shim, 0.005in thick, used in the transfer box to set the end float of the intermediate gear on its shaft. Selectiv...

Half Shaft – Rear LH – 10-Spline is the rear axle drive shaft for the left-hand side. It transmits drive from the differential out to the rear hub ...

Swivel pin housing Series

Half Shaft – Rear RH – 10-Spline Short is the rear axle drive shaft for the right-hand side. It carries the drive from the differential out to the ...

Front Swivel Pin Kit is a complete overhaul kit for the front axle swivel housings, the steering pivot assembly that allows the front hubs to turn ...

Stub Axle - rear stub axle carrying the hub and bearings at the rear axle. Bolted to the rear axle casing, it forms the fixed spindle on which the...

Body Mounting Shim used to set the correct clearance and alignment between the body tub and the chassis mounting points. This thin flat shim is us...

Swivel Housing Repair Kit for the front axle swivel assembly, covering one side of the axle. This kit excludes the swivel housing itself and suppli...

Swivel Pin Housing for the front axle, the chrome-finished swivel joint on which the steering swivel and hub assembly pivot. The housing bolts to ...

Trunnion

Shim is a 0.002" adjustment shim for the manual (non-power-assisted) steering box. It is fitted within the steering box to set the correct end-flo...

Swivel Pin

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Free-Wheeling Hub Repair Kit for 24-spline manual free-wheeling hubs. Manual free-wheeling hubs allow the front drive members to be disengaged fro...

Primary Pinion Bearing Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox casing. 2.05 mm thick, it control...

Door Latch Shim - Rear - a packing shim for the rear door anti-burst latch, part of the door lock and handle assembly. Fitted behind the latch on ...

Free Wheeling Hub Kit - manual locking front-axle hubs that connect or disconnect the front halfshafts from the road wheels. Set to free, the front...

Differential Pinion Bearing Shim - 0.068 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Differential Pinion Bearing Shim - 0.066 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Free-Wheeling Hub Kit - manually operated locking front hubs for a 24-spline front axle, fitted to the front stub axle in place of the standard dri...

Rear Left-Hand Half Shaft for the 10/24 spline rear axle. The half shaft transmits drive from the differential to the rear wheel hub. This left-ha...

Rear Axle Half Shaft - right-hand, 10/24 spline, for the Series III rear axle. This shaft transmits drive from the rear differential to the rear wh...

Differential Pinion Bearing Shim - 0.070 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Rear Axle Stub for the rear axle assembly on early Series Land Rovers. The axle stub is the outboard section of the rear axle shaft assembly, carr...

Rear Halfshaft for the Salisbury rear axle, 24-spline, right-hand side. The halfshaft transmits drive from the differential through the axle casin...

Rear Halfshaft for the E.N.V. heavy-duty rear axle, left-hand side. The halfshaft transmits drive from the differential through the axle casing to...

Swivel Pin Housing for the front axle, the chrome-finished swivel joint on which the steering swivel and hub assembly pivot. The housing bolts to ...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...