Land Rover Defender Parts

Brake Disc for the rear axle. This disc is the rotor that the rear caliper clamps to slow the wheel. Sized for the 20-inch brake disc and caliper ...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

External Torx Head Bolt, M8 x 48 mm, for the front propshaft flange. The bolt clamps the front propshaft flange to its mating drive flange. Its ex...

Connection - Water Outlet

Idler Pulley for the auxiliary drive belt, 70mm diameter, positioned within the front-end accessory drive system. The pulley guides and stabilises...

Brake Pad Set

Oil Filter Element and Seal

Water Pump is the engine-driven mechanical pump that circulates coolant through the cylinder block, cylinder heads and radiator to maintain engine ...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Wheel Spacer Set mounts between the wheel hub and the road wheel to increase track width, fitting over the hub and carrying a fresh set of studs fo...

Brake Pads - Less Springs

Brake Disc for the rear axle. This disc is the rotor that the rear caliper clamps to slow the wheel. Sized for the 20-inch brake disc and caliper ...

Bolt

Exhaust Clamp - 60mm exhaust joint clamp for the front section of the exhaust system, securing the downpipe to the centre silencer section. Clamps...

Valve Stem Seal seals the point where the valve stem passes through the cylinder head valve guide, controlling the oil reaching the stem and preven...

Wheel Nut for pressed steel road wheels, part of the wheel and hub fixing assembly. Seats against the wheel face and clamps the road wheel onto th...

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Lazer ST4 Evolution LED Spotlight - a compact four-LED auxiliary driving lamp producing a controlled long-range beam for forward illumination. The...

Lazer A-Pillar Mounting Kit - Utility-25 mounts Lazer Utility-25 and Utility-25 MAXX LED work lights at the base of the A-pillar for side illuminat...

CANNY is an advanced CAN interface developed by Lazer Lamps that enables the seamless installation of auxiliary lights on modern vehicles equipped ...

CANNY is an advanced CAN interface developed by Lazer Lamps that enables the seamless installation of auxiliary lights on selected vehicles utilizi...

Lazer Bumper Beam Mounting Kit - Linear-18 secures a Linear-18 LED light bar to the front bumper beam, behind the grille, for an integrated low-pro...

Land Rover Defender (2020+) Grille Light Integration Kit - Triple-R 750 A vehicle-specific grille integration kit designed for the Land Rover Defe...

Linear-18 LED Driving Light & Mounting Kit pairs a Lazer Linear-18 slimline LED light bar with a vehicle-specific grille mounting kit, so the l...

Linear-18 Elite LED Driving Light & Mounting Kit is a vehicle-specific grille integration kit that mounts a single Linear-18 Elite LED driving ...

Linear-18 Elite i-LBA LED Light & Mounting Kit is a vehicle-specific grille integration kit that mounts a single Linear-18 Elite i-LBA LED driv...

Lazer Bumper Beam Mounting Kit - Linear-6 secures a Linear-6 LED light bar to the front bumper beam for a clean, low-profile installation without v...

Bumper Beam Mounting Kit - Sentinel is a vehicle-specific bracket kit for mounting a pair of Lazer Sentinel LED driving lights to the front bumper ...

Grille Integration Kit - a vehicle-specific front-grille mounting kit that installs a pair of Lazer Triple-R 750 LED driving lights into the lower ...

Front Suspension Arm Bush - Inner Mount - the rubber-bonded pivot bush at the inner mounting point of the front suspension arm, within the front su...

Rear Crankshaft Oil Seal Fitting Tool guides and aligns the rear main crankshaft oil seal into its housing during engine rebuild work, part of the ...

Wheel Bearing - Rear, a component of the rear hub assembly. The rear wheel bearing carries the vehicle's rear load and allows the road wheel and h...

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Idler Pulley for the accessory drive belt system of the 2.0L I4 Ingenium (AJ200 / AJ20) petrol and diesel engine. The idler pulley guides the rout...

Plug cooling system bleed

Front Suspension Arm Bush - the rubber-bonded pivot bush that mounts the front suspension arm to the subframe, within the front suspension arm asse...

Front Strut Boot Kit renews the protective gaiter and mounting hardware for a front air suspension strut, part of the four-corner air suspension sy...

Wheelarch - LH is the left-hand plastic wheel arch panel forming the wheel housing on the vehicle body, shielding the surrounding body structure an...

Battery - 12V lead-acid battery of flooded, non-spillable construction, for the vehicle low-voltage electrical supply. Non-spillable construction ...

Timing Chain Kit for the valve timing drive of the Ingenium 2.0L 4-cylinder diesel engine (AJ200 series). The timing chain drive synchronises cran...

Alloy Wheel - 22-inch cast alloy road wheel in Style 5098, part of the road wheel and tyre assembly. Supplied as a bare wheel only. The tyre, valv...

Tubular Winch Bumper with A-Bar with Air Con for Terra Firma - Defender