Land Rover Defender Parts

Cross Rod Eye End for the steering linkage, left-hand-drive applications. This eye end fits to the steering cross rod (track rod) and provides the...

Heater Resistor Pack controls the heater blower motor fan speed within the blower assembly of the HVAC system. Wired into the blower motor circuit...

Heater Resistor Pack controls the heater blower motor fan speed within the HVAC system, on models with air conditioning. Wired into the blower mot...

Electronic Ignition Kit for the Rover V8 petrol engine with a points-type distributor. The kit replaces the mechanical contact points and condenser...

Turbo Oil Feed Pipe - oil supply pipe in the turbocharger lubrication circuit of the Td5 2.5L five-cylinder turbo diesel. It carries pressurised e...

Steel Wheel - 16 x 6.5 is a pressed-steel tubeless road wheel finished in black. Technical data: Size: 16 x 6.5 PCD: 5 x 165.1 mm Offset: ET20 ...

Water Shedder, Rear Side Door, Right-Hand Upper. Fitted to the upper section of the right-hand rear side door, it forms a barrier that directs wate...

Front Shock Absorber - Monotube Gas Pressure - front suspension damper of monotube construction. The damper controls the rate at which the front s...

Fuel Filter Shield is a protective cover fitted over the fuel filter assembly. It mounts over the filter housing and shields the filter body and i...

Rocker Cover Breather for the 200 Tdi and 300 Tdi diesel engines. It vents crankcase and valve-cover pressure from the rocker cover into the crankc...

Throttle Body Assembly is an intake air control unit within the diesel engine's air intake and emission-control system. It meters intake airflow t...

Transmission Brake Bolt for the transmission-mounted parking brake. The bolt secures a component of the transmission brake, which acts on the rear...

Side Sill Protectors - chequer plate covers for the body sills below the doors, within the exterior body protection assembly group. The sills take...

Washer for the bonnet insulation pad. This washer retains the sound- and heat-insulation pad against the underside of the bonnet, holding the pad ...

Inner Pinion Bearing for the Salisbury rear axle. This taper-roller bearing supports the inner end of the differential pinion shaft, carrying the ...

Body Washer, 22mm outer diameter, 6.5mm inner diameter. A flat washer that spreads the clamping load of a fixing across the mounting surface, prot...

H3 Halogen Bulb, 55W, single-filament. The H3 is a single-filament halogen capsule with a flying-lead connector, used in auxiliary lighting units ...

Ball Joint Repair Kit - Outer

Water Pump for the 2.4L Duratorq TDCi (Puma) diesel engine, forming part of the engine cooling circuit. Driven from the auxiliary belt, the pump c...

Intercooler Hose is part of the charge-air cooling circuit, connecting the intercooler to the adjoining charge-air tube. It carries pressurised, c...

Locating Dowel for the Rover V8 petrol engine. The dowel positions mating components accurately during assembly, ensuring correct alignment before...

Retrim Kit - Black - Outer Seat - No Adhesive

Front Propeller Shaft connecting the transfer box front output to the front axle differential. It transmits drive from the transfer box to the fro...

Retrim Kit - Black - Outer Seat - With Adhesive

Gudgeon Pin Bush - the small-end bush pressed into the connecting rod for the gudgeon pin. It forms the bearing surface between the gudgeon (pisto...

Cylinder Block Core Plug Seal sealing a core plug aperture in the cylinder block. It seals a casting core plug opening in the block, preventing co...

Dashboard Assembly Plate is a structural panel within the facia assembly, forming the mounting base onto which the instrument panel and dashboard t...

Bench Seat Backrest in techno fabric, forming the upright back section of the folding rear load area bench seat. This 810mm wide backrest mounts t...

Bench Seat Backrest in black vinyl, forming the upright back section of the folding rear load area bench seat. This 810mm wide backrest mounts to ...

Inlet Air Seal for the Solex carburettor connection on the 2.25L 4-cylinder petrol induction system. Seals the joint between the air intake and th...

Vent Assembly Knob for the dashboard air vent control on models without air conditioning. The knob fits onto the vent control lever and provides t...

Seat Retaining Strap Assembly for the rear inward-facing individual seat. The strap attaches the seat assembly to its mounting point and retains t...

Bolt Flanged hex-head bolt. Used to secure the timing belt and tensioner on diesel engines, and as a starter motor and drive plate fixing.

Bolt Mounting bolt for the power steering pump and front cover housing, and for air conditioning compressor and condenser mountings.

Anti-Squeal Shim - Set of 4 is a set of self-adhesive noise-dampening shims for disc brake pads. Each shim is cut to shape and bonded to the steel...

Gear Change Lever Knob for the transfer box gear change lever. The knob fits to the top of the transfer lever and forms the hand grip used to sele...

Cylinder Head & Sump Bolt Bolt used on the cylinder head and sump of the 2.5L Td5 five-cylinder turbo diesel engine.

Bolt Mounting bolt for the oil cooler/filter and turbocharger on the 2.5L Td5 five-cylinder turbo diesel engine.

Caliper Repair Kit for overhauling the front brake callipers. The kit contains stainless steel replacement pistons, the calliper seal repair kit an...

Fuel Filter Housing that holds the diesel fuel filter element within the fuel supply circuit. Mounted in the fuel line ahead of the injection syst...

Gear Selector Bush for the LT230 transfer box high/low gear change mechanism. The bush seats in the gear change housing and carries the high/low s...