Land Rover Defender Parts

Front Door Lower Hinge – Right Hand is the lower of the two hinges that mount the front door to the body, on the right-hand side. It is supplied i...

Front Door Upper Hinge – Right Hand is the upper of the two hinges that mount the front door to the body, on the right-hand side. It is supplied i...

Screw for body, trim and facia fixing applications. Used to secure roof trim, rear lamp fixings and facia rail panels. A general-purpose threaded ...

Spare Wheel Retention Plate - the plate that holds the spare wheel against the rear-door-mounted spare wheel carrier. It clamps over the wheel and...

Heater Air Intake Duct - the fresh-air intake ducting that feeds the heater assembly within the HVAC system. It channels outside air to the heater...

Distributor Vacuum Advance Unit in the ignition distributor assembly, mounting to the side of the distributor body. The vacuum capsule adjusts ign...

Side Window Screw - fixing screw for the side window assembly. Secures the side window frame and glazing components to the body aperture.

Fuel Return Valve in the diesel fuel return circuit, fitted within the fuel filter pipe assembly. The valve controls the flow of surplus fuel retu...

Hood Stick Retainer A retaining bracket for the hood sticks on the soft-top frame assembly. It secures the hood sticks - the transverse frame memb...

Power Steering Hose – Pump to Steering Box is the high-pressure feed line of the power steering hydraulic circuit. It connects the power steering ...

Steering Column Shroud Clamp is the upper clamp that secures the shroud around the steering column. It locates and retains the moulded cowl that e...

Heater Air Duct - fan cowl section of the heater air intake. This duct forms the fan cowl part of the heater intake, channelling air into the heat...

Rear Lamp Panel Cover - left-hand (LH) rear body panel that forms the surround and mounting face for the rear lamp cluster. It fits to the rear co...

Rear Lamp Panel Cover - right-hand (RH) rear body panel that forms the surround and mounting face for the rear lamp cluster. It fits to the rear c...

Tie Down Hook check strap bracket for the rear swing gate, part of the gate hardware. Anchors the gate check strap, retaining the swing gate and l...

Self Levelling Unit Retaining Strap secures the rear self-levelling suspension unit to its mounting, holding the unit in position and restraining i...

Rear Seat Clip - a retaining clip in the rear seat assembly, used to secure the seat frame to its mounting. Works alongside the rear seat frame an...

Power Steering Box is the recirculating-ball steering gear that converts rotation of the steering wheel into the side-to-side movement of the drop ...

Power Steering Box is the recirculating-ball steering gear that converts rotation of the steering wheel into the side-to-side movement of the drop ...

Blanking Plug closes off an unused aperture in the front bumper and chassis under-ride protection bar. Pushed into an open hole to seal it, the pl...

Outer Finisher - an external trim finisher fitted to the bodyside, used on the rear cab body panel and around the sliding side windows of the hard ...

Facia Vent Finisher - the trim surround that frames an air outlet on the dashboard facia. This finisher is for vehicles fitted with air conditioni...

Self Levelling Unit Gaiter - Upper is the protective rubber boot fitted over the upper ball joint of the rear self-levelling suspension unit. It s...

Windscreen Demist Vent Finisher - the trim that caps the demister outlet at the top of the facia, where the screen demist vent meets the base of th...

Fuel Filter Bracket mounts and supports the fuel filter assembly within the diesel fuel supply system. It secures the filter housing to the surrou...

Accelerator Pedal Mounting Bracket supports the accelerator pedal assembly within the throttle control system. It mounts the pedal to the bulkhead...

Rear Brake Disc - Wavy, Cross-Drilled & Grooved for the rear axle disc-brake assembly. The disc mounts to the rear hub and provides the frictio...

Truck Cab Bracket is a mounting bracket for the truck cab body. It secures the truck cab section to the vehicle. Fitted two per vehicle.

Rear Brake Disc - Pair for the rear axle disc-brake assembly, supplied as a matched set for both rear wheels. Each disc mounts to the rear hub and ...

Instrument Panel is the moulded facia structure forming the dashboard, carrying the instrument binnacle, switch panel and heater control assembly a...

Rear Lamp Cover Panel – LH is a body panel fitted at the left-hand rear of the vehicle, forming the mounting surround that locates and frames the r...

Rear Subframe Angle Bracket for the rear chassis and subframe assembly. The angled bracket provides a mounting and reinforcement point at the rear...

Wiper Mechanism Nut Plate for the windscreen wiper assembly. It provides the threaded mounting points that secure the wiper mechanism to the body,...

Hex Nut An M8 hexagonal plain nut. A metric steel fastener that threads onto a matching M8 bolt or stud to clamp components together, tightened wi...

Door Latch Mechanism Spacer for the rear end door latching assembly. It sets the correct standoff between the latch mechanism and its mounting fac...