Land Rover Defender Parts

Swivel Pin Housing Kit rebuilds the upper pivot of the front axle swivel housing, where the steering knuckle articulates on the axle. This is the v...

Front Right-Hand Brake Pipe for the hydraulic braking circuit, non-ABS systems. This pre-formed rigid steel pipe carries brake fluid through the f...

Piston Assembly - +0.020" Oversize for the 300Tdi 2.5L 4-Cylinder Turbo Diesel engine. This piston is machined to a diameter 0.020" (approximately...

Fuel Injector for the 2.5L 300TDi 4-cylinder turbo diesel engine. This direct injection fuel injector delivers metered, atomised fuel into the pre...

Oil Seal for the R380 manual gearbox extension case (rear/tail housing). It seals the output shaft where it exits the extension housing, retaining...

Bolt - Flanged Hex

Clutch Plate - 242mm

Connecting Rod Bearing Set for the 2.5-litre 4-cylinder engine, including the 200 TDi and 300 TDi diesels. These are the replaceable big-end shell ...

Engine Mounting Bracket - 3.5L V8

Oil Seal for the R380 manual gearbox extension case (rear/tail housing). It seals the output shaft where it exits the extension housing, retaining...

Raised Air Intake Fitting Kit - fitting hardware for the Terrafirma raised air intake, supplied separately from the intake itself. The raised air ...

Fitting Kit for Pacet Fan

Rear Stub Axle for the Salisbury rear axle assembly. The stub axle bolts to the outer end of the axle casing and forms the fixed spindle on which ...

Anti-Roll Bar Bush in the suspension anti-roll bar mounting, locating the stabiliser bar against the chassis. This polyurethane bush cradles the a...

Rear Light Lens for the rear stop and tail lamp. The red lens fits over the lamp body to cover the stop and tail bulb, transmitting the brake ligh...

Alternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...

Exhaust Valve Guide is pressed into the cylinder head and supports the exhaust valve stem, keeping it accurately centred as the valve opens and clo...

Clutch Slave Cylinder for the hydraulic clutch release system on Defender and Discovery 2 models fitted with the R380 manual gearbox. Mounted on t...

Heater Blower Duct Seal for diesel applications, fitted in the heater air intake. This foam seal sits between the air inlet duct and the heater blo...

ABS Wheel Speed Sensor - front sensor for the four-wheel anti-lock braking system. The sensor mounts in the front axle housing with its pole piece...

Retaining Clip for the output shaft oil seal on the MT82 6-speed manual gearbox. The clip locates and secures the oil seal within the gearbox hous...

Main Bearing Set 020 (Lc)

Idler Tensioner Pulley for the auxiliary (serpentine) drive belt system. Mounted on the automatic belt tensioner arm, the pulley bears against the ...

Rear Differential Drive Flange Kit for the Land Rover (Rover-type) rear axle. The drive flange mounts to the differential pinion and provides the ...

Engine Overhaul Gasket & Seal Set for the 200TDi diesel engine, covering the bottom end of the engine. This set provides the gaskets and seals...

Wheel Bearing Kit - a complete single-hub kit containing the bearings, seal and fixings to rebuild one wheel hub, suitable for either a front or a ...

Manifold Stud - M8 x 36 mm - for the Td5 2.5L 5-cylinder turbo diesel engine. The stud threads into the cylinder head to locate the manifold flang...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Main Bearing Set for the crankshaft main bearings in the engine bottom end. The bearing shells locate between the crankshaft main journals and the ...

Stop/Tail Lamp Assembly for the rear lighting circuit, combining the tail (running) light and stop (brake) light in a single LED unit. The assembl...

Bump Stop Tube - Weld On - Short is the short universal weld-on mounting tube for the TF140 hydraulic bump stop. It is welded to the chassis to ho...

Pump - Fuel Tank

Ignition Switch is the key-operated electrical switch mounted on the steering column, at the heart of the ignition and starting circuit. It select...

Conrod Bearing Kit - 0.010" Undersize for Land Rover four-cylinder petrol and diesel engines. Supplies a complete set of connecting rod big-end bea...

Lamp - Front Flasher

Latch

Front Brake Caliper, left-hand, for the non-vented (solid disc) front braking circuit. The caliper mounts to the front axle and houses the hydraul...

Lower Steering Column Universal Joint for the steering column assembly. This universal joint sits at the lower end of the steering shaft, transmitt...

Rear Fog Lamp Switch for the facia switch panel. The switch operates the rear fog lamp within the exterior lighting circuit.

Cam Cover Bolt for the Td5 2.5L 5-cylinder turbo diesel engine, securing the camshaft cover to the cylinder head. This is the flanged-head bolt th...

Kit - 7 Inch S/S Headlamp Fitting - Series - Defender

Radiator Rubber Mount for the engine cooling system. This rubber mounting locates the radiator in its support panel and cushions it against engine ...

Window Clip is a glass retaining clip for the door drop glass. It locates at the base of the sliding window glass in the front and middle doors, s...

Starter Motor - high-output unit for the 2.5L diesel engine, operating in the engine starting circuit. When energised through the starter solenoid...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Water Pump circulates coolant through the engine cooling circuit, drawing coolant from the radiator and driving it through the block and cylinder h...

Rear Lamp Guards - a pair of slatted steel guards fitted over the rear lamp assemblies to protect the lenses and lamp bodies from stone chips, bran...