Land Rover Defender Parts

Upper Turret Mounting Bracket, galvanised, forming part of the front coil spring and damper turret mounting on the chassis. The bracket provides t...

Trim Clip is a panel-retaining fastener used to secure interior door casing and exterior bodyside and drip-rail trim to the body. Part of the body...

Floor Plate Seal, a 1.6 m self-adhesive foam sealing strip used in the body and floor assembly. Applied along the edges of the floor plates and th...

Seat Back Foam is the moulded foam pad that forms the front seat backrest. It belongs to the seat and trim assembly. The foam fits between the sea...

Oil Seal for the R380 manual gearbox extension case (rear housing). It seals the output shaft where it exits the extension housing, retaining gear...

Rear Axle Half Shaft - LH, part of the disc-braked Salisbury rear axle assembly. The left-hand halfshaft transmits drive from the differential sid...

Front driveline propellor shaft connecting the transfer box output to the front axle differential within the drive mechanism. (60cm in 65cm) Trans...

Clutch Release Bearing Staple is the spring retention clip that secures the clutch release bearing onto the release fork. It holds the bearing in p...

Fir Tree Clip - a push-fit fastener that secures the door casing (interior door trim panel) to the door. The ribbed, tapered fir-tree stem pushes ...

Timing Belt for the 2.5L 4-cylinder naturally aspirated and turbo diesel engines (pre-TDi), part of the valve and injection-pump drive. The toothe...

Oil Cooler Pipe - the pipe carrying engine oil from the engine to the oil cooler within the lubrication cooling circuit of the 2.5L 4-cylinder TDi ...

Oil Cooler Pipe - the pipe carrying engine oil between the oil cooler and the engine within the lubrication cooling circuit of the 2.5L 4-cylinder ...

Oil cooler adapter gasket

Air Cleaner Hose - Cyclone is a crankcase-ventilation breather hose in the 300 Tdi air intake and engine breather system. It connects the cyclone ...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Power Steering Belt (Vee drive belt) for the 3.5L V8 petrol engine accessory drive. This belt runs between the crankshaft pulley and the power ste...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Seat Base Foam Cushion forms the lower outer section of the seat base assembly within the interior seating system. It provides the primary support...

Facia Louvre Vent Housing for air-conditioned models, mounted in the facia as part of the cabin air distribution system. It carries the directiona...

Top Link Bolt - 3/4 UNF x 4 inch hexagon head bolt for securing the front top link (upper radius arm) at the fulcrum and ball joint mounting points...

Bolt 5/16" UNF x 2" is a hex-head set bolt with a 5/16-inch Unified National Fine (UNF) thread at 24 threads per inch and a 2-inch shank length. I...

Fixing Screw for the front door hinge and check strap assembly. This screw secures the door hinge and the check strap (door-stay) to the body pill...

Rear Indicator Lamp for the exterior lighting system, fitted within the rear lamp cluster. It provides the rear directional turn-signal indication...

Differential Drive Flange for the Salisbury rear differential. It bolts to the differential pinion shaft and forms the coupling face to which the r...

Water Temperature Sender threads into the cooling system and measures engine coolant temperature, feeding the signal to the dashboard temperature g...

4WD High Gear Selector Spring for the transfer box four-wheel-drive selector mechanism. The spring acts on the high-range four-wheel-drive selecto...

Lower Swivel Pin O-Ring for the front axle swivel housing assembly. It seals the joint at the lower swivel pin, where the steering arm and lower pi...

Bottom End Gasket Set for the overhaul of the 2.25L diesel engine (3- and 5-main-bearing), covering the gasket and joint requirements of the lower ...

Bolt with a 3/8" UNF (Unified National Fine) thread and a 1-7/32" length. A standard imperial-thread fastener for chassis, driveline and body fixi...

Heater Control Finger Grip The finger grip fitted to a heater control slider on the heater (HVAC) control panel, operated in the up/down plane. It...

Grommet - rubber blanking grommet for the transmission (gearbox) tunnel cover. This rubber grommet seals the access aperture in the gearbox tunnel...

Tailgate Chain Cover - a pair of protective sleeves that fit over the two retaining chains supporting the rear tailgate. Each chain links the tail...

Hexagon Nut with a 7/16" BSF (British Standard Fine) thread. A standard nut cut to the British Standard Fine thread form used throughout the fixin...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Front Cover Gasket sealing the engine front cover to the cylinder block on the V8 EFI petrol engine. The gasket forms the joint between the timing...

Clutch Slave Cylinder for the hydraulic clutch release system, fitted to the LT77 and LT95 manual gearboxes. The cylinder receives hydraulic press...

Door Card Fixing Kit for the interior door trim assembly of the Defender, in black. This kit provides the black-coloured rivets and fasteners requ...

Steering Damper - Girling

Oil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...

Stop/Tail Lamp Assembly for the rear lighting circuit, combining the tail (running) light and stop (brake) light in a single unit. The assembly mo...

Con Rod Bearing Set for the 2.25L four-cylinder petrol engine. The set provides the big-end shell bearings that carry the connecting rods on the c...

Wheel Nut - secures an alloy road wheel to the hub, forming the threaded clamping interface between the wheel and hub. It uses a wide-stud profile...

Flasher Relay controls the direction indicator and hazard warning lamp circuit, switching the lamps on and off at the regulated flash rate. It plu...

Lower Steering Column Universal Joint for the steering column assembly. This universal joint sits at the lower end of the steering shaft, transmitt...

The Interior Door Card Snap Sac Trim Clips are designed to securely fasten your vehicle's door card and trim pieces. Fitment: all models

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Front Door Hinge - Lower, Right-Hand - lower hinge for the right-hand front door, mounted between the door and the body A-pillar. It forms the low...

Wiper Delay Relay for the front windscreen wiper circuit, controlling the intermittent (delay) wipe function. It times the pause between wipe cycl...