Land Rover Defender Parts

Autogear Power Syn 75W90 5L

Rear Axle Case Bolt for the Salisbury rear axle. The bolt clamps the axle casing joint of the Salisbury (heavy-duty) rear axle, keeping the housin...

Front Brake Caliper Piston is a 41mm piston that operates in the front brake caliper, part of the braking hydraulic circuit for solid disc brakes. ...

Valve Guide for the Rover V8 cylinder head. Pressed into the cylinder head, the guide supports the valve stem and keeps the valve concentric with ...

O-Ring sealing the dipstick tube where it enters the cylinder block on the V8 petrol engine. Fitted around the lower end of the dipstick tube, thi...

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Choke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...

Choke Cable is the manual choke control cable in the carburettor fuel system, running from the dashboard choke knob to the carburettor choke lever....

Heater Hose - Series 3 RHD

Primary Pinion Shim - 2.00 mm for the four-speed V8 gearbox. Used during gearbox assembly or rebuild to set the correct end-float and bearing prel...

Primary Pinion Bearing Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox casing. 2.05 mm thick, it control...

Selector Shaft Spring - V8

Inner Ring

Hose

Ignition Switch for the steering-column lock, diesel specification. The switch is the electrical unit that fits into the steering-column lock barre...

Rear Halfshaft for the Salisbury rear axle, 24-spline, right-hand side. The halfshaft transmits drive from the differential through the axle casin...

Vacuum Actuator O-Ring for the LT95 4-speed gearbox. This O-ring seals the vacuum actuator fitted to the LT95 transfer case mechanism, used on V8-p...

Gearchange Spring

Spring Pin for the LT95 four-speed gearbox, used in the gear selector mechanism. The hollow, sprung roll pin locates and retains selector componen...

Gasket gearbox front cover and oil pump. LT95 4-speed gearbox - Early 110 V8, - S3 109" stage 1 V8, - 101" F.C. - Early Range Rover Classic

Cable Clip for securing wiring harnesses and cables in Land Rover vehicles. Sold individually.

Brake Pedal Pivot Bush for the brake pedal assembly. It seats in the pedal box and forms the bearing surface on which the brake pedal pivots on it...

Radiator Overflow Bottle fitted to the cooling system on Series II, Series III, and 101 Forward Control Land Rovers. This plastic reservoir collec...

Intermediate Exhaust Pipe for the 2.6L 6-cylinder petrol engine. This is the centre section of the exhaust system, connecting the front pipe to th...

Hex Nut - 7/16 UNF fixing nut. Used on the fuel pipe unions of the 3.5L V8 twin-carburettor petrol engine. Also supplied as part of a service kit.

Gearbox Selector Pad for the LT77 five-speed manual gearbox. Fits the 5th gear selector within the selector and yoke assembly, forming the bearing...

O-Ring for use in two distinct applications on classic Land Rover engines. On the Series IIA 2.6L 6-cylinder engine, this O-ring seals the cylinde...

Washer - a plain flat washer with a 10.5mm internal diameter, sized for M10 fasteners. It seats under a bolt head or nut to spread the clamping lo...

Sump - 2.25 Petrol/Diesel - 2.5 Petrol is the engine oil sump (oil pan) for the 2.25L 4-cylinder petrol, 2.25L 4-cylinder diesel, and 2.5L 4-cylind...

Spring Shackle Distance Tube for the rear leaf spring shackle assembly. This spacer tube sets the correct spacing between the shackle plates, maint...

Tappet Adjuster is the adjustment screw used to set valve clearance in the cylinder head of Land Rover Series 4-cylinder engines. The screw thread...

Tappet Screw - the valve-clearance adjusting screw in the rocker gear of the four-cylinder engine (3-bearing crankshaft), part of the valvetrain. ...

Distance Piece - a machined spacer in the axle and suspension assembly, specified for the 1-Ton Military configuration. It sets the standoff betwe...

Brake & Clutch Reservoir Tank Kit, a replacement for the original single fluid reservoir that fed both the brake and clutch master cylinders. ...

Tappet Guide (guide only) locates and retains the tappet roller assembly within the engine block, maintaining correct alignment of the tappet as it...

Handbrake Catch Pawl, the ratchet claw of the transmission parking brake mechanism. It engages the toothed quadrant on the handbrake lever, lockin...

Starter Motor Solenoid for the Lucas 2M100 starter motor, part of the engine starting circuit. Mounted on the starter body, the solenoid throws th...

Differential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...

Upper Rear Door Seal, the rubber weatherseal for the top edge of the rear door aperture. It seals the upper line of the rear door against the body...

Front Door Check Strap, part of the front door hinge and retention hardware. Connecting the front door to the body pillar, the check strap limits ...

Door Latch Shim - Rear - a packing shim for the rear door anti-burst latch, part of the door lock and handle assembly. Fitted behind the latch on ...

Engine Plug is a core (welch) plug that seals the casting holes in the engine. Fitted to the cylinder block, cylinder head water jacket and inlet ...

Seat Base Corner Capping in plastic. Fitted at the outer corners of the front seat base frame, this capping provides a neat finished edge and prote...

Heater Control Mounting Plate for left-hand drive applications. Fitted within the heater control assembly in the cab interior, this plate provides ...

Sill Panel Rear 109 Not Station Wagon - LH

Rear Sill Panel for the right-hand side of the body understructure on long wheelbase (109 inch) models. Fitted at the rear sill position, this pane...

Heater Air Intake Trim fits the front wing air intake of the heating and ventilation system. It finishes the fresh-air intake aperture in the wing...