Land Rover Defender Parts

Bolt with Washer - M8 x 50 mm bolt supplied with its washer, used as a structural fixing on the body and on engine ancillary mountings. Applicatio...

Mud Flap - a moulded rubber rear mud flap with a ribbed face, hung behind the rear wheel to intercept water, mud and stones thrown up by the tyre. ...

Front Direction Indicator Bulb - 12V 28W, serving the indicator position within the front lamp assembly. At 28W this bulb is rated above the more ...

Dowel for the cylinder block to transmission joint on the 2.4 L and 2.2 L TDCi Puma diesel engines. The dowel seats in the rear face of the cylind...

Brake Light Switch

Spacer fitted between the axle driveshaft and the constant velocity joint in the front axle assembly. It sets the axial position of the constant v...

Spacer fitted between the axle driveshaft and the constant velocity joint in the front axle assembly. It sets the axial position of the constant v...

Front Axle Reinforcing Kit - a two-piece set of pre-cut, weld-on reinforcing sections for the front axle casing, profiled to suit the long-nose Rov...

Stop & Tail Lamp - 24V is a combined rear stop and tail lamp unit for vehicles running a 24 V electrical system. The unit carries both functio...

Bulkhead Light Mounting Kit A pair of powder-coated fabricated steel brackets for mounting small to medium spotlights on the bulkhead. The bracket...

Number Plate Lamp - LED is the rear licence plate illumination unit within the rear lighting circuit. It mounts above the licence plate at the rea...

Stainless Steel Braided Brake Hose Kit - Goodridge flexible brake hoses supplied 2in longer than standard for vehicles running a suspension lift. ...

Number Plate Lamp - Chrome is the rear licence plate illumination unit within the rear lighting circuit. It mounts above the licence plate at the ...

Spare Wheel Cover - 235/85 R16 - vinyl cover for an externally mounted spare wheel, sized to a 235/85 R16 tyre. The cover pulls over the assembled...

LED Side Repeater Lamps - Amber - a pair of sequential (dynamic) LED repeaters with an amber lens for the front wing side repeater positions in the...

Top Shock Bush Kit - replacement upper mounting bushes for Pro Sport and 8-stage adjustable remote reservoir shock absorbers. The bushes seat in t...

LED Side Repeater Lamps - Clear - a pair of sequential (dynamic) LED repeaters for the front wing side repeater positions in the exterior lighting ...

LED Side Repeater Lamps - Smoked - a pair of sequential (dynamic) LED repeaters with a smoked lens for the front wing side repeater positions in th...

Shock Ball Joint Kit - service kit for the spherical mounting joint at the end of a performance shock absorber. The ball joint is the principal we...

Anti-Roll Bar Bush in polyurethane, 25.4mm bore, for the rear anti-roll bar mounting. The bush sits where the bar is clamped to its chassis bracke...

TF Wing Top Foam Gaskets - 07 On

Plain Washer - flat steel washer from the hardware and fixings group. It is fitted under a bolt head or nut to spread the clamp load over the join...

Wind Deflectors - Rear - Defender

Universal Joint - replacement universal joint for wide angle and double cardan propshaft assemblies in the driveline. Sits between the propshaft y...

Receiver Hitch Pin - retaining pin for a 2in receiver hitch assembly. The receiver housing has a 2in internal bore that accepts a 2in square-secti...

Goodridge Brake Hose Kit - +2"

Stainless steel braided brake hose kit, three-line, +2" extended length. The flexible hoses carry hydraulic pressure across the moving joint betwee...

Anti-Roll Bar Fitting Kit - Front

Extreme Rear Body Corners - Pair - 90

Gear Lever and Transfer Box Lever Knob Set in polished alloy with a silver finish, replacing the standard plastic knobs on the main gear lever and ...

Internal Spacer for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The spacer fits inside the bump stop to shorten the ...

Damper Rod - replacement 12" shaft for the 2.5" smooth-body competition damper (TF488), supplied as a rebuild service part. The rod carries the pi...

Valve for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The TF140 is a monotube, nitrogen-charged unit adjustable betw...

Seal Kit - Bump Stop

Nylon Pad for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The pad forms the contact face at the end of the bump stop...

Switch mounting bracket for a single differential lock switch, forming part of the electric locking differential control circuit. The bracket give...

Seal Kit - 11" Travel Shock

Replacement Damper Shaft for the 11 inch travel Mega Sport monotube shock absorber. The shaft carries the damping piston and passes through the se...

Switch mounting bracket for two differential lock switches, forming part of the electric locking differential control circuit. The bracket gives b...

Panhard Rod Bush Kit - replacement polyurethane bush set for heavy-duty adjustable Panhard rods, within the axle lateral-location assembly. The Pa...

Off-Road Foam Air Filter Element for the air box in the engine induction system, dimensioned to sit in the standard housing in place of the paper e...

Foam Air Filter - Snorkel Filter - TD5

Bump stops, standard height - front or rear axle. The bump stop absorbs the last part of suspension compression, cushioning axle-to-chassis contac...

Foam Air Filter - Defender 300TDi

Receiver Hitch Pin - the retaining pin for the integrated 2" receiver hitch on the TF883NAS rear step tow bar assembly. The pin passes through the...

Fuel Cooler Guard - an underbody protection plate for the diesel fuel cooler in the fuel supply and return circuit. The fuel cooler is mounted ben...