Land Rover Defender Parts

Anti-roll bar bush

Radius Arm Bush mounts at the axle end of the front radius arm, within the front suspension radius arm and axle location assembly. It forms the co...

Upper Link Bush for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. It seats in the upper (top) link to provide ...

Steering UJ upper

Oil seal

Wheel spacer kit fitted between the wheel hub and road wheel within the wheel mounting assembly. The spacers move the wheel mounting face outward...

Lower Arm Link – Rear is a rear suspension locating link connecting the rear axle to the chassis on coil-sprung suspension. It locates the axle fo...

Nyloc Nut with an M8 thread - a nylon-insert locking nut used as a self-locking fastener in threaded assemblies. A nylon collar set into the top o...

Exhaust Manifold Locking Washer that secures the exhaust manifold fixings to the cylinder head. The tab washer fits under the manifold bolt or nut...

Cable Clip secures wiring harnesses, breather pipes and similar runs to the body, chassis or panel. It locates in an 8mm mounting hole and holds t...

Clutch Release Fork operates inside the bellhousing as part of the manual transmission clutch release mechanism. Pivoting on its mounting in the c...

Flanged Head Screw is an M6 x 12mm machine screw with an integral flange beneath the head. The flange spreads clamping load over a wider area and ...

Shock Absorber Bush Set - a set of four polyurethane bushes for the shock absorber mountings within the suspension damper assembly. Each bush seat...

Plain Washer - imperial-dimensioned flat washer with an internal diameter of 7/16 inch and an outer diameter of 13/16 inch. Used in general fasten...

Rear Output Shaft Flange for the LT230 two-speed transfer case. The LT230 distributes drive to the front and rear propshafts. This flange mounts o...

Rear Brake Caliper, right-hand side, for the rear braking circuit on models fitted with solid (non-vented) rear discs. The caliper clamps the brake...

Screw used as a securing fastener in the pedal box area and in brake pipe routing. This screw retains the cover plate at the top of the pedal box,...

Hex-head bolt, 3/8" UNC thread, 3/4" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and sock...

Hex-head bolt, 5/16" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Ignition heater plug timer glow plug relay

Hose pump to box

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the fuel injection pump. It transmits pedal movement to the...

Exhaust Olive for the exhaust system. This tapered sealing ring fits into the slip joint between two exhaust pipe sections. As the joint clamp is ...

Radius Arm Washer is a plain washer used at the radius arm mounting in the suspension. It seats under the radius arm fastener to distribute clampi...

Flanged Head Screw, M8 x 12 mm. A metric set screw with an integral flange beneath the hexagon head that spreads clamping load and helps resist loo...

Clip

Collapsible spacer transfer box

Speedometer Drive Housing is the pinion (spindle) housing that fits to the rear flange of the LT230 transfer box. It carries the speedometer drive ...

Cylinder Head Bolt for the 200TDi and 300TDi 2.5-litre direct-injection turbo diesel engines. It secures the cylinder head to the engine block, cla...

Rear Crankshaft Packing Strip (T-Piece) forms part of the rear crankshaft oil seal arrangement at the back of the cylinder block. The T-piece pack...

Fuel Lift Pump for the low-pressure fuel supply circuit of the 2.5L 300TDi turbo diesel engine. This engine-mounted mechanical diaphragm pump draw...

Oil Filler Cap closing the engine oil filler neck on the rocker cover. It seals the filler aperture to keep the lubrication system closed and prev...

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. This plastic plug cl...

Dipstick tube O-ring 200 & 300TDi, TD5

Oil Filter Adaptor Gasket Seals the oil filter adaptor housing to the cylinder block within the lubrication circuit of the 300 TDi 2.5L diesel engi...

A/C Drive Belt drives the air-conditioning compressor on the 2.5L 300TDi diesel. Run from the crankshaft pulley, it transmits drive to the air-con...

Exhaust Manifold Gasket for the 200 TDi diesel engine, sealing the joint between the exhaust manifold and the cylinder head. It seals each exhaust...

Oil Cooler Thermostat - the thermostatic control valve in the engine oil cooling circuit. It regulates oil flow to the oil cooler in response to o...

CuNiFer Clutch Pipe, 1/4" outer diameter, supplied for the clutch hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough t...

Jubilee Clip - 21-44mm is a worm-drive hose clip with a 21-44mm clamping range. The band is tightened by a captive worm screw to clamp small- to m...

Bolt 1/4" UNF x 2" is a hex-head set bolt with a 1/4-inch Unified National Fine (UNF) thread at 28 threads per inch and a 2-inch shank length. It ...

Static Lap Seat Belt for the second-row seating position, forming part of the interior occupant restraint system. The non-retractable, fixed-lengt...

Bonnet Grommet is a rubber grommet fitted within the bonnet assembly. It lines the aperture through which the bonnet prop rod or release mechanism...

Accelerator Cable for the 200TDi throttle linkage. The cable runs from the accelerator pedal to the throttle lever on the fuel injection pump. Dep...

Pipe Clip, a routing clip that retains pipework and small-bore lines against the chassis, body or transmission casing. It supports breather, fuel,...

Head Gasket - 3.5L V8 - Metal is the cylinder head gasket for the 3.5L V8 petrol engine, sealing the joint between a cylinder head and the engine b...

Oil Pump Relief Valve Spring for the 3.5L V8 petrol engine lubrication system. The spring sets the opening pressure of the oil pump pressure-relie...

Oil Filler Cap O-Ring seals the oil filler cap to the rocker cover. It forms an oil-tight seal at the cap-to-cover joint, preventing oil leakage a...