Land Rover Defender Parts

Radius Arm Bush - Front is the flexible mounting bush at the front radius arm-to-chassis location. The radius arm locates the front axle longitudi...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...

Silicone Intercooler & Turbo Hose Kit - a set of silicone charge-air hoses for the 300Tdi turbo and intercooler circuit, replacing the standard...

Bottom cover seal

Universal Joint for the propeller shaft assembly, transmitting rotational torque between adjoining shaft sections while permitting the angular move...

Clutch Slave Cylinder Repair Kit - a service kit for reconditioning the hydraulic clutch slave cylinder on the R380 5-speed manual gearbox. The cl...

Taper Roller Bearing - shaft bearing for the R380 five-speed manual gearbox. A taper roller bearing carries both radial load and axial thrust, loc...

Brake Pad Set for the front axle disc brake assembly, for use with solid (non-vented) front discs. The pads locate within the front calipers and cl...

Connecting Rod Bearing Set for the 2.5-litre 4-cylinder engine, including the 200 TDi and 300 TDi diesels. These are the replaceable big-end shell ...

Anti-Roll Bar Bush in the suspension anti-roll bar mounting, locating the stabiliser bar against the chassis. It cradles the anti-roll bar at its ...

Spring Retaining Plate in the rear suspension, securing the upper end of the rear coil spring. It locates and clamps the top of the coil spring ag...

Push Rod - a valvetrain component in the overhead-valve layout of the Rover V8 engine. It sits between the camshaft-driven tappet and the rocker a...

Modular Steel Wheel - Black - 7J x 16 A modular steel road wheel finished in black, sized 7J x 16 with an ET08 offset. The steel construction suit...

Bracket

Propshaft Spacer Kit (25mm) - a driveline spacer fitted between the propshaft flange and the transfer box or differential flange to restore the pro...

Propshaft Gaiter (Sliding Joint) is the flexible rubber boot that seals the sliding splined joint of the propshaft in the drivetrain. The sliding ...

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.

M12 Nut used as a fastener at several chassis and running-gear locations, including the swivel pin housing, drive shaft fixings and front brake cal...

Crankshaft Pulley mounts on the front of the crankshaft on the 200TDi 2.5L turbo diesel engine and drives the auxiliary drive belts. This pulley i...

Bolt 5/16" UNC x 5" is a long mounting bolt for the coolant pump and power steering pump on the 3.5L V8 petrol engine. Its length carries the powe...

Front Coil Spring - Medium Duty, +2" Lift (Terrafirma). These front coil springs raise ride height by approximately 2 inches over standard and are...

Changeover Relay - 5-Pin - Green is a standard 5-pin changeover relay used across multiple electrical circuits. This relay is used in various appl...

Inertia Switch in the fuel supply and engine electrical circuit. It cuts electrical power to the fuel pump on a sudden impact or severe deceleratio...

Spring Washer for use as a locking fastener component across Land Rover assemblies. A helical split spring washer providing resistance against fas...

Clutch Cover is the pressure plate assembly of the clutch, bolting to the engine flywheel within the clutch and gearbox coupling. Its diaphragm sp...

Gearbox Bearing for the R380 5-speed manual gearbox, measuring 35 × 72 mm. Fitted within the R380 transmission assembly, this rolling-element bear...

Shock Dropper - Rear - Pair: zinc-plated steel relocated rear shock absorber top mounts that lower the upper mounting point by 50mm. By relocating...

Rear Shock Absorber provides damping control within the rear axle spring and damper assembly for suspension set up with extended travel. Twin-tube...

Front suspension shock absorber designed to control spring oscillation and maintain tyre contact with the road surface. Twin-tube low-pressure ni...

Exhaust manifold stud

CV Joint Circlip - the retaining circlip that secures the constant velocity (CV) joint to the front drive shaft. The circlip locates in a groove o...

Main Bearing Set for the Rover V8 engine, in the standard size. The main bearings are the crankshaft's principal support bearings, sitting between ...

Snatch Block - a winch recovery pulley used to redirect a winch line or to double its effective pulling capacity. Rated for a 10-tonne working load...

Hex Head Bolt - 1/4" UNF thread, 5/8" long, with a hexagonal head. A general-purpose imperial fastener with a Unified Fine (UNF) thread form, driv...

Kickdown Cable Assembly for the automatic transmission control. The cable links the throttle to the automatic gearbox, relaying throttle position s...

Gearbox Sump Gasket for the ZF 4-speed automatic transmission, sealing the joint between the transmission oil pan (sump) and the gearbox casing. T...

Power steering seal kit

Steering Lever - RHD for the Adwest power steering box, supplied with the ball joint fitted. Also known as the drop arm, the lever clamps onto the...

Fuel Pump Seal for the fuel tank sender unit. This seal seats at the mounting flange of the fuel pump and sender unit where it interfaces with the ...

Locknut is a self-locking M10 nut used as a general threaded fastener across the vehicle. Its locking feature resists loosening under vibration, m...

Nut - M8 plain low-profile nut, sold individually. A standard metric M8 nut in the low-profile (thin) form. Used across gearbox, suspension, axle,...

Radius Arm Bush Set - Front - Polyurethane is a set of four polyurethane bushes for the front radius arm-to-chassis mountings. The radius arms loc...

Spill Rail for the 300 TDi fuel injection system. The spill rail links the leak-off unions at the top of the injectors and carries surplus fuel fro...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Fulcrum Bracket for the rear suspension A-frame assembly. The bracket provides the chassis mounting point for the A-frame ball joint, which locate...

Alloy Wheel is a single-piece 16 x 7-inch alloy road wheel finished in black. It has a five-stud 5x165 mm bolt pattern and an ET20 offset, which s...

Breather hose rocker cover

Nut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.