Land Rover Defender Parts

Sealing Washer for the cylinder block oil jet adaptor on the 2.5L 4-cylinder diesel engine. Seals the jet adaptor against the cylinder block. Fitt...

Sealing Washer fitted at the engine front cover. Provides a leak-tight seal at a fastener or fitting on the front cover assembly.

Plain Washer - a flat load-spreading washer used at the body-to-chassis mount fixings. Fitted under the bolt head or nut, it distributes clamping ...

Autotec Reverse Light Switch for CDU51/CDU51L manual-gearbox applications. It completes the reverse lamp circuit when reverse is selected. Applica...

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Gearchange Housing for the LT77 5-speed manual gearbox. Mounted on top of the gearbox, it carries the gear selector mechanism and locates the gear...

Differential Lock Link Assembly for the LT230 transfer box, fitted to vehicles with the LT77 or LT85 5-speed manual gearbox (28D prefix). This lin...

Plenum Chamber Gasket for the V8 EFI petrol engine, part of the air intake and induction assembly. The gasket seals the joint at the plenum chambe...

Oxygen Sensor (lambda sensor) for the V8 EFI petrol exhaust system on catalyst-equipped applications. It measures residual oxygen in the exhaust ga...

Camshaft for the valvetrain of the 4.0/4.6L V8 petrol engine. Mounted in the cylinder block and driven from the crankshaft, the camshaft lobes act...

Heater Inlet Hose is a moulded coolant hose in the cabin heater circuit of the 200TDi 2.5L turbo diesel engine. It carries hot coolant from the en...

Kit - Timing Belt - 200TDi

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Crankshaft Oil Seal - Front - 300TDi

Bolt

Countersunk Screw for the Transmission Brake Assembly. The countersunk head sits flush within the mating surface, maintaining correct alignment and...

Anti-roll bar bush used in the front suspension anti-roll bar assembly, providing the compliant mounting interface between the anti-roll bar and it...

Valve Stem Cap is a hardened cap that sits over the tip of the valve stem in the cylinder head valve train. It forms the wear interface between th...

Core Plug - Cylinder Block Expansion Port is a pressed-steel sealing plug installed in the outer face of the cylinder block to close the casting ap...

Radius Arm to Chassis Bush - Front locates the front radius arm to its chassis mounting bracket within the coil-sprung front axle suspension. It f...

Circlip - Output Shaft Flange used within the transfer box output flange assembly to retain the output shaft bearing and associated components in p...

Timing Belt for the camshaft drive of the 300 TDi diesel engine, running within the timing belt and tensioner assembly at the front of the engine. ...

Main Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...

Fuse rated at 7.5A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 7.5 amps, the fuse breaks the connection...

Repair Washer - M10 for use in suspension, axle and body fastening applications. A large-diameter flat washer that distributes the clamping load o...

Washer - a general-purpose fixing washer used across multiple body, brake and chassis assemblies. It spreads the clamping load of a bolt or nut ov...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Alternator Mounting Screw for the Rover V8 petrol engine alternator assembly. This screw secures the alternator to its mounting bracket on the eng...

Gearbox Breather for the gearbox and transfer case assembly. This breather is located on the gearbox or transfer case casing and vents internal pr...

Torque Converter Housing Cover Gasket for the automatic transmission bell housing. It seals the lower access cover on the torque converter housing...

Bolt - M8 x 40mm standard metric hex-head fastener for use across engine, gearbox, body, and chassis assembly applications.

Set Screw - a fully threaded hexagonal-head setscrew with an M10 metric thread and a 20 mm length. A general-purpose fixing used at fastening point...

Front Shock Absorber Bush Kit for the front suspension assembly. Bush kit for the front shock absorber mounting, providing the rubber isolation be...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Radius Arm Bush Kit - Chassis End, Front (Terrafirma). A set of four uprated polyurethane bushes for the front radius arm mountings, replacing the...

Engine Mounting Rubber for the 2.5L 200 TDi engine mounting system. This rubber-to-metal mount locates between the engine mounting foot and the cha...

Starter Motor for V8 petrol engines, operating within the engine electrical starting system. The solenoid-actuated pinion engages the flywheel rin...

Shock Absorber - Front - +2" Travel for the front coil spring suspension system, designed for use with a 2-inch suspension lift. The extended-trav...

Anti-Roll Bar Kit comprising both front and rear anti-roll bars for the suspension system, supplied complete with standard rubber bushes and fittin...

Front Half Shaft for the right-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant vel...

ABS Wheel Speed Sensor - front sensor for the four-wheel anti-lock braking system. The sensor mounts in the front axle housing with its pole piece...

Cylinder Head Gasket Set for the 2.5L 200TDi turbo diesel engine, supplying the top-end gaskets and seals required when the cylinder head is remove...

Conrod Bearing Kit - 0.010" Undersize for Land Rover four-cylinder petrol and diesel engines. Supplies a complete set of connecting rod big-end bea...

Rocker Assembly Aluminium - LH

Power Steering Pipe - Pump to Box is the high-pressure hydraulic feed line connecting the power steering pump outlet to the steering box inlet. Th...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Rocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...