Land Rover Defender Parts

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

Oil Separator Drain Hose for the crankcase ventilation system on the 2.5L naturally aspirated diesel and 200TDi turbo diesel engines. It drains th...

Front Cover Gasket sealing the timing cover to the front face of the cylinder block on the 300TDi 2.5L turbo diesel engine. It forms the oil-tight...

Pulley

Flywheel Housing Stud for the 2.5L four-cylinder diesel engine. It secures the flywheel housing to the rear face of the engine, locating the housin...

Joint Washer is a sealing washer fitted at a bolted or threaded joint on the 4-cylinder diesel engine, forming a seal between the mating faces to p...

Distributor Drive Gear for the Rover 3.5L V8 petrol engine. The gear forms part of the ignition distributor drive assembly, transferring rotationa...

Enhance the performance and handling of your Defender 110 with this rear coil spring pair. Designed for heavy-duty use, these yellow springs are pe...

Silicone Turbo & Intercooler Hose Kit - a three-piece set of silicone charge-air hoses for the 300Tdi turbo and intercooler circuit, replacing ...

Spring Retaining Plate for the front coil spring suspension. The plate seats the upper end of the front coil spring against the chassis spring seat...

Fuel Tank Sender Wrench is a special service tool for the fuel tank sender unit assembly. It engages the metal locking ring that retains the fuel ...

Clutch Slave Cylinder Repair Kit for the hydraulic clutch release circuit on V8 petrol applications. The clutch slave cylinder is actuated by hydr...

Hex-Head Bolt with a 7/16" UNF (Unified National Fine) imperial thread and a 2" shank length. A fastener used in the manual steering box mounting ...

Bolt with a 3/8" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing applic...

Bolt - M12 x 60mm is a metric hexagon head bolt used across a wide range of assembly applications on Land Rover vehicles. Thread specification M12...

Bolt - M10 x 130mm is a hex-headed metric fastener with a 10 mm nominal thread diameter and a 130 mm shank length. It serves as a general mounting...

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Locking Nut for the steering linkage, securing the adjustable joint onto a heavy-duty drag link or steering rod. Once the joint is set to the corre...

heavy duty spring front RR/disco pair, like DA4201 and TF014.

Polyurethane Suspension Bush Kit A complete polyurethane bush set that replaces the original rubber suspension bushes across the chassis-mounted su...

Anti-Roll Bar is the rear stabiliser bar within the suspension system, mounted transversely across the rear axle. Connected to the suspension thro...

ABS Pump Relay for the Anti-lock Braking System electrical circuit. A normally open, black-bodied relay that controls power supply to the ABS pump...

Spring Nut - Metal U-Clip for body panel and electrical component fixings across a range of Land Rover models. This metal U-clip spire nut clips o...

Vacuum Pump O-Ring that seals the diesel vacuum pump at its mounting joint. The vacuum pump supplies the depression used by the brake servo on die...

Self-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...

Distributor Drive Gear - V8

Steering Valve Ring is a PTFE sealing ring used within the rotary valve of the Adwest power steering box. It seals between the pressure lands of t...

Sedimentor Drain Plug Seal for the sedimentor in the diesel fuel supply. The sedimentor separates water and heavier contaminants from the fuel ahea...

Distributor O-Ring, the sealing ring for the ignition distributor on the 3.5L V8 petrol engine. The O-ring seals the distributor base where it loc...

Union Nut for the fuel pipe in the fuel delivery system. This M12 union nut clamps a fuel pipe to its mating union or component port, drawing the ...

Bolt & Lockwasher for securing the inlet manifold on the V8 petrol engine. Supplied as a bolt with its matching lockwasher. The imperial 5/16"...

Cylinder Head Bolt for the Rover V8 engine, 7/16" UNC thread. Used to secure the cylinder head to the block on the Rover 3.5L, 3.9L and 4.0L V8 en...

Cylinder Head Bolt - a 7/16" UNC x 2.71" medium-type bolt for the Rover V8, part of the cylinder head fixings. This is the medium-length head bolt...

Cylinder Head Dowel for the V8 petrol engine. The dowel is a locating pin fitted to the cylinder block deck that positively registers the cylinder ...

Ball Steel Bearing

Oil Pump Relief Valve Spring - sets the pressure at which the oil pump's relief valve opens. It holds the relief valve plunger closed against the ...

Wheel Stud - Front Drive Shaft Hub is a press-fit threaded stud for the front drive shaft hub assembly. It provides the fastening point that secure...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Crankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...

Washer - a plain flat washer used as a general-purpose fastening component across many assemblies on the vehicle. Fitted under a bolt head or nut,...

Sedimentor Drain Plug with Seal for the diesel fuel filter assembly. Fitted at the base of the sedimentor bowl, this plug allows the bowl to be dr...

Sedimentor O-Ring for the diesel fuel filter assembly. This rubber sealing ring seals the sedimentor bowl against the filter head, preventing fuel...

Flat Washer with a 3/8" bore, fitted under a bolt head or nut to spread the clamping load over a wider area and protect the mating surface.

Swivel Pin Retaining Bolt A fixing bolt for the front axle swivel pin housing. It secures a swivel pin to the swivel pin housing, retaining the pi...

Hose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...

Oil Relief Valve Sealing Washer seals the oil pressure relief valve within the engine oil pump assembly. It is fitted at the relief valve in the l...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...