Land Rover Defender Parts

Door Trim Clip for the interior door casing assembly. Fir-tree fastener that secures the door trim casing to the door frame, locating it in the pa...

Oil Cooler Pipe O-Ring for engine and transmission oil cooling circuits. This O-ring seals pipe fitting and hose connection joints in the oil cool...

Breather Hose for the 300 TDi crankcase ventilation system. The hose carries crankcase breather (blow-by) gases from the engine breather outlet ba...

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...

Clutch Clip - Push Rod to Lever for the hydraulic clutch actuation system. This spring clip secures the clutch slave cylinder push rod to the clut...

Drain Plug for differential casings and LT230 transfer boxes. The tapered plug seals the oil drain, fill, and level holes in differential and axle...

Wheel Nut - secures an alloy road wheel to the hub, forming the threaded clamping interface between the wheel and hub. It uses a wide-stud profile...

Distributor Cap for the ignition distributor on the V8 EFI engine. The cap seats over the distributor and carries the high-tension current from th...

Stub Axle Oil Seal - Inner

Exhaust Manifold Gasket for the 3.5L V8 petrol engine. This gasket seals the joint between the exhaust manifold and the cylinder head, preventing ...

Panhard Rod Bush for the front suspension lateral location assembly. This rubber bush is pressed into the Panhard rod eye and provides the complia...

Grommet

Oil Seal Retainer for the front axle swivel housing assembly. This retaining plate holds the swivel housing oil seal square against the chrome swiv...

Rocker Cover Gasket for the Rover V8 petrol engine, sealing the rocker (valve) cover to the cylinder head. The gasket seats between the cover flan...

Gear Oil - EP80W90 extreme-pressure gear lubricant for manual gearboxes, transfer cases, and axle drives. The EP80W90 grade combines extreme-press...

Clip is a multi-purpose retaining clip used to secure cables, harnesses and small components in their mountings. It locates and holds items such a...

HOLDER - BULB - SINGLE POLE - D1/D2/DEF ALL/F1/P38

Swivel Pin Gasket seals the joint between the swivel pin housing and the axle case on the front axle. It sits at the mating face where the swivel ...

Exhaust Rubber Mounting suspends the exhaust system from the chassis, supporting the silencer and pipework at its mounting points. The rubber elem...

Brake Pipe Clip - single-bore retaining clip for securing a rigid brake pipe to the chassis or body structure. This clip holds the brake pipe in i...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Thermostat - 88°C for the cooling system of V8 petrol engines. The thermostat regulates coolant flow between the engine block and the radiator, al...

4-Pin Relay is a multi-purpose electromechanical switching relay used throughout the vehicle's electrical system, where a low-current control signa...

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...

Hub Outer Oil Seal for the front and rear wheel hub assemblies. Located at the outer end of the hub, it retains the wheel-bearing grease within the...

Brake Union Nut - Metric Thread for the hydraulic brake pipe circuit. This union nut seals and secures brake pipe connections at the unions throug...

Engine Oil - 15W40 Multigrade mineral engine lubricant for older petrol, diesel, and LPG engines. 15W40 multigrade viscosity provides reliable lub...

Power steering seal kit

Thermostat Housing Gasket Seals the thermostat housing to the cylinder head within the cooling system of the 300 TDi 2.5L turbo diesel engine. It ...

Reverse & Differential Lock Switch is a plunger-operated switch used in the manual gearbox and transfer box electrical circuits. The same swit...

Stub Axle Locking Plate - Mudshield

Rocker Cover Gasket for the 2.5L 200TDi diesel engine, sealing the joint between the rocker cover and the cylinder head. Installed at the top of t...

Exhaust Bush - Male is the male-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the cor...

Drive Flange for the front hub assembly. The drive flange bolts to the outer face of the hub and engages the splined end of the axle half shaft, t...

Front Stub Axle for the front hub and swivel pin housing assembly at the front axle. The stub axle passes through the swivel pin housing and provi...

Differential Pinion Oil Seal for the final drive, with a 4-bolt flange (LR-type, non-Salisbury axle). The single-lip seal sits at the front of the ...

Front Hub Lock Washer for the front hub and driveshaft assembly. This tabbed washer seats between the hub nut and the hub bearing assembly on the ...

Gearbox Plug Sealing Washer for LT76 and LT77 manual gearbox drain, level, and inspection plugs. This sealing washer fits beneath the thread of ge...

Coolant Temperature Sensor - V8 EFI for the engine management system. This sensor monitors coolant temperature and sends a continuous signal to th...

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. O-ring is included. ...

Manifold gasket 300TDI

Bump Stop - Front for the front suspension travel limiting assembly. This rubber bump stop limits upward suspension travel at the front axle, prov...

Screen Washer Pump for the rear window wash circuit. This electric pump draws washer fluid from the reservoir and delivers it under pressure to th...

Brake Pipe Clip - Double secures and routes rigid hydraulic brake pipes within the braking system. This double clip retains two brake pipes at a s...

Elbow Gasket seals the coolant outlet elbow, or thermostat housing, to the inlet manifold on the V8 petrol engine, forming part of the engine cooli...

Water Pump Inlet Gasket - seals the water pump inlet housing against the engine front cover within the coolant circuit. It forms the joint between...

Suspension and Chassis Mounting Bolt used across multiple suspension and chassis linkage positions. This hexagon bolt secures components including...