Land Rover Defender Parts

Thrust Washer 1.45mm Diff - LT230

Thrust Washer for the differential assembly within the LT230 transfer box. This 1.35mm thrust washer sits within the LT230 centre differential, co...

Thrust Washer is a 1.25mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Thrust Washer is a 1.15mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Drain Plug Washer is the copper sealing washer for the drain plug on the LT77 manual gearbox. It seats between the magnetic drain plug and the gea...

Half Shaft Shim is a 1.50mm selective shim used in the axle drive shaft and hub assembly. It sets the endfloat of the half shaft drive member with...

Needle Bearing - LT77 5-Speed Gearbox - Mainshaft This needle roller bearing supports the mainshaft gear cluster within the LT77 5-speed manual ge...

Needle Bearing - LT77 supports a mainshaft gear on the LT77 5-speed manual gearbox mainshaft, allowing the gear to rotate freely on the shaft. It ...

O-Ring - Diff Lock Selector Shaft - LT230 Transfer Case This O-ring seals the differential lock selector shaft where it passes into the LT230 tran...

Gasket

Clutch Release Arm Pivot Plate for the LT77 5-speed manual gearbox. Mounts inside the clutch bellhousing and provides the pivot point for the clut...

Gearbox Oil Seal for the extension case of the LT77 five-speed manual gearbox, sealing the mainshaft output collar. The seal runs on the collar at...

Drive Meter Speedo Gear Yellow 22 Teeth

Dowel is a precision locating pin that aligns mating components during assembly, setting their position accurately and relieving the securing bolts...

Differential Pinion Bearing Shim - 0.070 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Flanged Nut - M6 flanged hex nut for use across a wide range of Land Rover assemblies including engine, drivetrain, body, braking, and electrical a...

Oil pump relief valve washer V8

Dowel Ring locates the cylinder head to the block deck on the 200 TDi and 300 TDi diesel engines. Seated in the block face at the head-to-block jo...

Exhaust Manifold for the 3.5L V8 petrol engine, supplied without heat transfer cover. The manifold collects exhaust gas from one cylinder bank and...

Injector Clip for V8 EFI fuel injection systems, used in the fuel delivery assembly at the intake manifold. This retaining clip secures the fuel i...

Piston Cooling Oil Jet Relief Valve - part of the engine lubrication system, fitted in the cylinder block oil feed to the piston cooling jets. It r...

Valve Cotter in the cylinder head valvetrain, locking the valve spring retainer to the valve stem. The cotters seat as a pair into the machined gr...

Valve Spring Cap for the cylinder head valve train. The spring cap seats on top of the valve spring and locates against the split collets on the v...

Fuel Pipe for the 200 TDi diesel fuel delivery circuit. Connects the fuel filter outlet to the injection pump inlet, carrying filtered fuel to the...

Exhaust Downpipe with Cat is the front section of the exhaust system for the 300TDi engine, incorporating the catalytic converter. It bolts to the...

Bracket

Upper Radiator Mounting Bracket that locates and secures the top of the radiator in the cooling system. Fitted to four-cylinder TDi and Td5 applic...

Hose

Oil Cooler Adaptor Gasket for the Rover V8 petrol engine, part of the engine lubrication circuit. It seals the joint between the oil cooler adapto...

A/C Belt Tensioner Cover for the air conditioning belt drive on 300TDi engines. This cover fits over the tensioner pulley assembly in the A/C auxi...

Cylinder Head Gasket for the 2.5L 200TDi and 300TDi diesel engines, supplied in the 1.4mm compressed-thickness grade (identified by two holes). Th...

Cylinder Head Gasket for the 2.5L 200TDi and 300TDi diesel engines, supplied in the 1.3mm compressed-thickness grade (identified by a single hole)....

Turbocharger for the forced-induction system of the 2.5L 300 TDi diesel engine, supplied complete with the mid manifold section. Driven by exhaust...

Tappet Adjusting Screw for the 2.5L 300 TDi turbocharged diesel engine, fitted in the rocker arm of the valvetrain. Threaded into the rocker arm t...

Power Steering & ACE Pump Pulley mounts to the hydraulic pump drive shaft and is turned by the engine's auxiliary drive belt. Drives the power...

Sound Deadening Pad is an acoustic pad fitted to the rocker cover on the 2.5L 300TDi turbo diesel engine. It damps mechanical noise radiating from...

Oil Dipstick Tube, V8

Stepper Motor for the V8 EFI petrol engine, part of the idle air control system on the intake plenum. Acts as the idle air control valve, metering...

Throttle Position Sensor (Potentiometer) for V8 petrol engines with Electronic Fuel Injection (EFI). Mounts on the throttle body and signals throt...

Camshaft for the Rover V8 EFI petrol engine (3.9L, 4.0L and 4.6L variants). Mounted centrally in the cylinder block, the camshaft is driven from t...

EGR Pipe Hose for the 2.5L 300TDi 4-cylinder turbo diesel engine. This rubber hose forms part of the exhaust gas recirculation (EGR) circuit, conn...

Viscous Fan Coupling drives the engine cooling fan on the 3.9L and 4.0L V8 EFI petrol engine. The temperature-sensitive coupling varies fan speed ...

Fuel Injector delivers atomised diesel into the combustion chamber of the 2.5L 300TDi engine. Fitted to non-EGR applications.

Inlet Valve for the cylinder head valvetrain of the Rover V8 petrol engine (3.5L, 3.9L, 4.0L and 4.6L variants). It seats in the cylinder head inl...

Injector Clamp Stud - 200Tdi / 300Tdi is the threaded stud used to secure the injector hold-down clamp in the cylinder head of the 200Tdi and 300Td...

Camshaft Pulley O-Ring - the seal fitted at the camshaft pulley on the front timing drive. It seals the joint between the camshaft nose and its dr...

Viscous unit

Valve Cotter (split collet) for the Rover V8 petrol engine valve train. Locks the valve spring retainer to the valve stem, holding the spring unde...