Land Rover Defender Parts

Elbow Gasket seals the coolant outlet elbow, or thermostat housing, to the inlet manifold on the V8 petrol engine, forming part of the engine cooli...

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Piston Rings - 200TDi - Standard for the 2.5L 200TDi four-cylinder turbo-diesel engine at standard bore dimensions, for use during engine overhaul....

Towing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...

Drive Member - Heavy Duty

Flywheel Bolt securing the flywheel to the rear flange of the crankshaft. Used on four-cylinder petrol and diesel engines, including the 200TDi an...

Thermostat for the 2.5L 300TDi diesel engine, operating within the thermostat housing at the top of the cooling circuit. The thermostat regulates ...

Shock Absorber Bush is a rubber mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chassis and axle attachme...

Fuel Injector for the fuel injection system of the 2.5L 200 TDi diesel engine. The injector atomises high-pressure diesel delivered from the injec...

EGR Valve to Pipe Gasket for the diesel exhaust gas recirculation (EGR) system. The gasket seals the flanged joint between the EGR valve and the r...

Radius Arm Bush Set - Front - a set of polyurethane bushes for the front radius arm axle-end mountings. The radius arm locates the front axle long...

Brake Pad Set for the rear axle disc brakes, fitting the rear brake calipers. The friction pads clamp against the rear brake discs under caliper a...

Connecting Rod Bearing Set - a set of big-end bearing shells for the Rover V8 petrol engine. The connecting rod bearings are the split shell beari...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Coolant Temperature Sensor threads into the cylinder head and reports engine coolant temperature to the engine management system and the instrument...

Injector Sealing Washer seals each fuel injector into the cylinder head within the diesel fuel injection system, for 200 TDi and 300 TDi turbo-dies...

Coolant Temperature Transmitter is the engine coolant temperature sender, threaded into the cylinder head where it reads the temperature of the coo...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

16 x 7 Maxtrac Blindo Alloy Black 5 x 165PCD Offset Et15

Clutch Hose for the 300 Tdi 2.5L turbo diesel, forming the flexible section of the clutch hydraulic actuation circuit. The hose links the rigid pi...

O-Ring for the LT230 Transfer Box, used at multiple sealing positions within the unit. This O-ring is fitted at several locations in the LT230 two...

Coolant Temperature Sensor - V8 EFI for the engine management system. This sensor monitors coolant temperature and sends a continuous signal to th...

Inlet Valve operates in the cylinder head valvetrain of the 2.5L 300TDi turbo diesel engine. It seals against the inlet valve seat and opens to ad...

Flanged Nut - M10 flanged fastener. The integral flange spreads the clamping load over a wider area and resists loosening under vibration, removin...

Camshaft operates the valvetrain of the 2.5L 300TDi diesel engine. Its lobes actuate the pushrods to open and close the inlet and exhaust valves.

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...

Drive Belt Air conditioning compressor drive belt for the 200TDi turbo diesel engine, poly-vee (multi-rib) construction. Drives the A/C compressor...

Inlet & Exhaust Manifold Gasket - 300TDi

Cylinder Head for the 300 TDi 2.5L four-cylinder turbo diesel engine, supplied as a bare casting without valves. The head bolts to the top face of...

Front Half Shaft for the right-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant vel...

Front Axle CV Joint, heavy-duty, 24-spline, for the front drive shaft. The constant velocity joint sits at the outer end of the front axle shaft an...

Hose - Oil

Taper Roller Bearing for the front output shaft of the LT230 transfer box. Installed within the LT230 transfer case differential lock and output s...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Clutch Slave Cylinder Repair Kit - a service kit for reconditioning the hydraulic clutch slave cylinder on the R380 5-speed manual gearbox. The cl...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Camshaft Oil Seal - radial oil seal for the 2.5L 300 TDi turbo diesel engine, fitted in the front timing cover within the timing gear assembly. Th...

Connecting Rod Bearing Set for the 2.5L 4-cylinder engine, supplied in 0.030" oversize. These are the big-end shell bearings that fit between the ...

Oil Filler Cap closing the engine oil filler neck on the rocker cover. It seals the filler aperture to keep the lubrication system closed and prev...

Gasket Set

Coupling - Viscous Borgwarner

Fuel Stop Solenoid for the 200 Tdi and 300 Tdi 2.5L turbo diesel engine, mounted on the fuel injection pump. Held open while energised through the...

Swivel Joint Washer located within the Swivel Pin Housing Assembly, sealing the interface between the swivel housing flange and the axle beam face....

Exhaust Manifold Gasket for the 200 TDi diesel engine, sealing the joint between the exhaust manifold and the cylinder head. It seals each exhaust...

Layshaft Bearing - taper roller bearing supporting the layshaft in the R380 5-speed manual gearbox. The bearing carries the countershaft (layshaft...

Camshaft Seal - Rear

Piston Assembly - +0.020" Oversize for the 300Tdi 2.5L 4-Cylinder Turbo Diesel engine. This piston is machined to a diameter 0.020" (approximately...