Land Rover Defender Parts

Oil Separator Drain Hose for the 300 Tdi 2.5L 4-cylinder turbo diesel engine, part of the crankcase ventilation system. It returns the oil collect...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit on manual transmission applications. Mounted at the clutch housing, it receive...

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Swivel Ball Inner Bearing Housing for the front axle swivel assembly. It locates and supports the inner bearing within the swivel ball, maintaining...

Timing Cover Plate Gasket sealing the timing gear cover plate on the 300Tdi 2.5L four-cylinder turbo diesel engine. The gasket forms the joint bet...

Rocker Cover Sealing Washer seals a rocker cover retaining bolt on the 200Tdi 2.5L turbo diesel engine. The washer fits under the rocker (valve) c...

O-Ring sealing the front crankshaft (timing) sprocket within the timing case of the 2.5L 300TDi turbo diesel engine. It forms an oil-tight seal ar...

Brake Vacuum Pump for the 300 TDi 2.5L turbo-diesel engine, mounted on the engine as part of the brake vacuum circuit. Driven mechanically by the ...

Coolant Temperature Sensor threads into the cylinder head and reports engine coolant temperature to the engine management system and the instrument...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Anti-Rattle Clip secures the linkage rod within the door latch and lock mechanism. It retains the lock linkage rod at its connection point, holdin...

Power Steering Reservoir

Coolant Temperature Sensor threads into the engine coolant circuit and reports coolant temperature to the instrument and engine management systems....

Taper roller bearing for the swivel pin housing assembly within the front axle system. This bearing supports radial and axial loads generated at ...

Tab Washer for the steering drop arm retaining nut on the Adwest steering box. Fitted beneath the drop arm nut on the steering box output shaft, t...

Shock Absorber Bush - Polyurethane is a polyurethane mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chas...

screw M5 x 12

Plenum Hose - Breather T-Piece to Plenum

Water Pump for the Rover V8 EFI petrol engine, supplied with gasket. The water pump sits in the engine cooling circuit and is belt-driven from the...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

The Interior Door Card Snap Sac Trim Clips are designed to securely fasten your vehicle's door card and trim pieces. Fitment: all models

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Timing Belt Kit for the camshaft drive of the 2.5L 300 Tdi turbo-diesel engine. The timing belt synchronises crankshaft and camshaft rotation to m...

Plain Washer - a flat, load-spreading washer with a 1/4 in (6 mm) bore and 5/8 in outside diameter, approximately 1/16 in thick, finished in Sherar...

Fuel Filter Housing Assembly for the fuel delivery line on carburettor petrol engines, including the 3.5L V8. This assembly mounts in-line between...

Washer Jet Tubing is the flexible hose used within the windscreen washer system, supplied in 1 m lengths. It carries washer fluid from the reservo...

Bleed Screw - Metric is the bleed nipple for a disc brake caliper. Threaded into the caliper body, it is opened during brake bleeding to release t...

Fuel Pipe Clip securing fuel pipe within the fuel delivery system. The clip retains and locates the fuel line along its routing, holding it agains...

Spring plate

Handbrake Locking Plate for the rod-operated transmission handbrake - the drum-type parking brake mounted at the transfer gearbox output. The plat...

Crankshaft Oil Seal seals the front timing cover where the crankshaft nose passes through it. Fitted to the 2.5L 300 TDi diesel engine, the seal r...

High Note Horn, the high-pitched unit of the vehicle's dual-tone horn system. It sounds together with the low note horn to produce the two-tone au...

Plain Washer with a 6 mm (1/4") bore, a general-purpose flat washer for use with M6 fasteners. Fitted beneath a bolt head or nut to spread the cla...

Tab Washer locks the drop arm retaining nut on the Adwest power steering box, its tab folded against a flat on the nut to stop it working loose und...

Upper Gasket Kit for the 300Tdi 2.5L 4-cylinder turbo diesel engine. The kit supplies the gaskets and seals needed to refit the cylinder head afte...

Track Rod End for the steering linkage, with a left-hand thread. The track rod end forms the ball-jointed connection between the steering link and...

Water Pump O-Ring Set provides the sealing rings for the coolant pump, sealing the pump to its mounting face and preventing coolant leakage at the ...

Nyloc Nut with an M16 thread - a nylon-insert locking nut used on heavily loaded suspension and driveline fixings. A nylon collar set into the top...

Brake Pipe Clip (double) for ABS-equipped braking systems, used to route and secure rigid brake pipes. The double form holds two brake pipes side ...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Exhaust Spacer Tube is a short pipe section within the exhaust system. It spaces and connects adjacent exhaust sections at a flanged joint, settin...

Brake T-Piece - Metric is a three-way junction in the brake hydraulic circuit. It joins three brake pipes at a single union, typically distributin...

Clutch Release Fork - Heavy-Duty is the pivoting lever in the clutch release mechanism that acts on the release bearing. Operated by the clutch sl...

Gasket for transfer box gearchange lever housing plate LT230 with LT85, LT77, Chrysler 3-speed or ZF 4-speed automatic. Also part of gasket kit RTC...

Camshaft Oil Seal seals the camshaft on the 2.5L 4-cylinder diesel engines, including the 200TDi. Fitted at the front of the engine where the cams...

Camshaft Oil Seal - radial oil seal for the 2.5L 300 TDi turbo diesel engine, fitted in the front timing cover within the timing gear assembly. Th...

Oil Pump Gasket for the engine lubrication system, sealing the oil pump to its mounting face on the cylinder block. It maintains a leak-free joint...