Land Rover Defender Parts

Exhaust Downpipe - De-Cat for the front section of the exhaust system, fitted downstream of the turbocharger outlet on TD5 diesel applications. Th...

Main Bearing Set for the Rover V8 engine, in the standard size. The main bearings are the crankshaft's principal support bearings, sitting between ...

Snatch Block - a winch recovery pulley used to redirect a winch line or to double its effective pulling capacity. Rated for a 10-tonne working load...

Bolt - a hexagonal-head bolt with a 5/16" UNC (Unified Coarse) imperial thread and a 3/4" length. Used as an engine-assembly fixing, including cams...

Gearbox Sump Gasket for the ZF 4-speed automatic transmission, sealing the joint between the transmission oil pan (sump) and the gearbox casing. T...

Blanking Plug - a threaded plug that seals an unused port or aperture in an engine casting or housing. It closes off a threaded opening not requir...

Fuel Cooler for the diesel fuel return circuit. Mounted in the return line between the fuel injection system and the tank, it dissipates heat pick...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Head Gasket - TD5 - 1-Hole seals the joint between the cylinder head and cylinder block on the Td5 2.5L 5-cylinder turbo diesel engine. The 1-hole...

Timing Chain Guide for the Td5 2.5L 5-cylinder turbo diesel, part of the timing chain drive assembly at the front of the engine. The guide runs al...

Cylinder Head for the Td5 2.5L 5-cylinder turbo diesel engine, later type. The cylinder head seals the top of the engine block, forming the combust...

Handbrake Shoe Set for the transmission handbrake. Part of the transfer-box-mounted drum parking brake. The shoes expand against the inside of the...

Differential Flange Mud Shield - a protective shield fitted at the differential pinion drive flange. It sits behind the drive flange, where the pr...

External Circlip for the R380 manual gearbox selector yoke. The circlip locates in the groove on the selector yoke and retains it in position with...

Seat yoke

Bolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...

Plenum to Water Jacket Gasket seals the joint between the plenum chamber and the water-jacketed intake manifold in the Rover V8 EFI induction syste...

Sealing Washer for the 2.5L Td5 engine, used to seal threaded and banjo unions in the fuel and cooling systems. Seated against a fitting's mating ...

Crankshaft Woodruff Key for the 2.5L 300TDi and 2.5L Td5 diesel engines. This semicircular key seats in a slot machined into the crankshaft nose an...

Hydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...

Spare Wheel Cover for an externally mounted spare wheel sized 7.50x16 (235/85R16). Constructed from soft vinyl, it shields the spare wheel and tyr...

Spring Seat is the lower seat for the rear coil spring, forming the located surface that the base of the spring sits on. It positions and retains ...

Bulb - 501 is a 12V 5W capless wedge-base bulb, designated W5W. The one-piece glass base pushes directly into the holder, with the contact wires f...

Differential Pinion Bearing Spacer used in the axle differential assembly across a broad range of Land Rover models from 1965 onwards. This spacer...

Transmission Brake Drum for the transmission (hand) brake. Mounts to the transfer box rear output flange and houses the transmission brake shoes, ...

Interior Trim Fastener in Bahama Beige, for securing rear interior trim panels in seven-seat Discovery 1 variants. This plastic push-in fastener c...

Relay

Front Propshaft transmits drive from the transfer box front output flange to the front axle differential pinion. Forming part of the four-wheel-dr...

Screw - a self-tapping pan-head fastener used in interior trim assembly. It cuts its own thread into the panel or moulded mounting boss to secure ...

Polyurethane Boot - Defender - Discovery 1/2 - RRC - P38

Cam Cover Gasket for the 2.5L Td5 5-Cylinder Turbo Diesel engine. This gasket seals the camshaft cover to the top of the cylinder head, preventing...

Rear Coil Spring Spacers, +2" - a pair of suspension spacers for the rear coil springs that raise ride height by approximately 2 inches (50 mm). E...

Pipe and Hose Retaining Clip - Engine is a small-bore clip used to retain pipes and hoses at multiple points across the engine bay and fuel system ...

Gearbox Heat Shield fitted to the transmission mounting assembly, protecting the surrounding components from exhaust and drivetrain heat. By reduc...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Camshaft Cover Grommet sealing the camshaft cover to the cylinder head on the Td5 2.5L five-cylinder turbo diesel engine. The grommet forms a stat...

USB Charging Socket - a dashboard-mounted charging socket that fits a standard factory switch aperture, giving a flush, integrated appearance in pl...

Conrod Bearing Set for the Td5 2.5L 5-cylinder turbo diesel engine, supplied at standard size. The connecting rod bearings (big-end bearings) sit ...

Main Bearing Set for the Td5 2.5L 5-cylinder turbo diesel engine. The main bearings are the crankshaft journal bearings seated in the cylinder blo...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the big-end bearing shells that sit between the connecting rods and the cranks...

Fitment: - Classic Defender: TD5 diesel models - Discovery 2: All TD5 diesel models and All V8 EFi petrol models - Range Rover P38: 2.5L 6 Cyl B...

Push Rod - a valvetrain component in the overhead-valve layout of the Rover V8 engine. It sits between the camshaft-driven tappet and the rocker a...

Fuel block connector assembly (+hoses) TD5 L318;L316

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Flange Bolt for the Td5 2.5L five-cylinder turbo diesel engine. The integral flanged head spreads clamping load across the joint face and removes ...

Flange Bolt - M6 × 10mm is a metric flanged-head fastener used across a wide range of assembly points on Land Rover vehicles. The integrated flang...

Self-Tapping Screw - Black is an M8 x 25mm self-tapping screw with a black finish. The self-tapping thread cuts its own mating thread as it is dri...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...