Land Rover Defender Parts

Vacuum Pump Rotor Blade for the engine-driven brake servo vacuum pump. The blade runs within the rotor of the vacuum pump, generating the vacuum t...

Backplate Brake >KA - Defender - LH

Backplate Brake >KA - Defender - RH

Rectifier for the alternator. The rectifier pack converts the alternator stator's three-phase alternating current into the direct current required ...

Platform Assembly - the front bonnet-locking platform of the front-end bodywork. It carries the grille aperture and the bonnet locking mechanism, a...

Circlip

Woodruff Key that locates the timing gear and pulley on the crankshaft of the Rover V8 petrol engine. The key sits in the crankshaft keyway to pos...

Shackle Plate, the side plate of the spring shackle assembly that forms the swinging link between the leaf spring eye and the chassis shackle brack...

Spring Shackle connecting the end of a leaf spring to the chassis bracket, allowing the spring to lengthen and shorten as it deflects under load. ...

Retainer for the steering damper mounting, part of the track rod and steering damper assembly. This stem washer locates on the steering damper mou...

Drive Screw retaining the direction-indicator switch clamp. A hammer-drive screw used to secure the indicator switch clamp, and the indicator cowl...

Rocker Shaft Assembly forms part of the valvetrain (rocker gear) on the overhead-valve V8 petrol engine. Mounted on pedestals above the cylinder h...

Improve your Defender 90, Discovery 1, or Range Rover Classic's braking performance with this stainless steel rear caliper piston.

Front Brake Caliper Piston - Stainless Steel is a 41mm stainless steel piston that operates in the front brake caliper, part of the braking hydraul...

Cylinder Head Bolt - a 7/16" UNC x 2-1/4" short-type bolt for the Rover V8, part of the cylinder head fixings. This is the shorter of the head bol...

Cylinder Head Dowel for the V8 petrol engine. The dowel is a locating pin fitted to the cylinder block deck that positively registers the cylinder ...

Stop Cable Diesel Without Steering Column Lock RHD

Brake Drum - 10 Inch for the wheel brake assembly on early short wheelbase Series Land Rovers. Fits the 10-inch drum brake system used on SWB (88"...

Gasket gearbox front cover and oil pump. LT95 4-speed gearbox - Early 110 V8, - S3 109" stage 1 V8, - 101" F.C. - Early Range Rover Classic

Exhaust Valve Guide is pressed into the cylinder head to support and align the exhaust valve. It locates the valve stem so the valve seats squarel...

Flywheel Ring Gear (starter ring gear) for the diesel flywheel, part of the clutch and flywheel assembly. The toothed ring is fitted around the fl...

o-ring sealing shaft reverse gear LT95 4-speed - S3 109" stage one V8 - 110" V8 4-speed manual - RRclassic 4- speed manual - 101" Forward Control

Crankshaft Thrust Washer - 0.010in oversize, supplied as a pair. Fitted at the centre main bearing of the four-cylinder engine to control cranksha...

Track Rod Tube - 109.5cm - Part-Threaded Ends

Spring Shackle Distance Tube for the rear leaf spring shackle assembly. This spacer tube sets the correct spacing between the shackle plates, maint...

Flywheel Ring Gear for four-cylinder petrol engines. The ring gear is shrink-fitted to the periphery of the flywheel and meshes with the starter mo...

Distance Piece - a machined spacer in the axle and suspension assembly, specified for the 1-Ton Military configuration. It sets the standoff betwe...

Radiator Panel for the front-end assembly on Series III models. This panel forms the surround and support structure for the radiator, integrating w...

Replace or upgrade the front outer wing panel on your Series 2/3 Land Rover with this aluminium panel designed for Right-Hand Side (RHS) and Left-H...

Air Vent Mechanism - operating mechanism for the dash-mounted fresh-air ventilator. Controls the opening and closing of the bulkhead air vent flap...

Glass Retainer is the vertical glazing retainer for the rear end door assembly. Holds the rear door glass along its vertical edge.

Front Rope Retaining Hook - Left Hand Side for the soft-top hood system on Series and Defender Land Rovers. This hook is part of the hoodstick and...

Hook for the soft top retaining rope, part of the hood and hoodstick assembly. Secures the rope that runs along the soft top drain channels.

Layshaft Sleeve - bearing sleeve fitted to the layshaft (countershaft) in the LT67 main gearbox. Provides the running surface for the layshaft clu...

Screw - 10 UNF x 3/8 is a fixing in No.10 UNF (Unified National Fine) thread, 3/8 inch in length, used in fascia and dash assembly applications. Fi...

Small End Bush (gudgeon pin bush) for the connecting rod small end on Land Rover diesel engines. The small end bush is a precision bronze bush pre...

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Coolant Tube forming the primary coolant path between the cylinder block and the water outlet. This aluminium tube carries coolant from the engine...

Water Pump is the engine-driven mechanical pump that circulates coolant through the cylinder block, cylinder heads and radiator to maintain engine ...

Coolant Outlet Pipe - Upper - SC

Portable Jump Starter and Air Compressor - a handheld 12V power pack combining a battery jump starter, power bank, tyre inflator and LED work light...

Defender 90 Scale Model - a 1:76 scale diecast model of the Land Rover Defender 90, finished in Pangea Green. The model reproduces the Defender 90...

Halogen Bulb - H4 100/80W (Non-CE). Dual-filament headlight bulb rated 100W high beam and 80W low beam, providing increased light output over the s...