Land Rover Defender Parts

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Exhaust Stud Nut for front exhaust system connections. This nut secures exhaust pipe sections to the manifold or downpipe studs, maintaining a gas...

Propshaft Washer for the front propshaft flange connection. The washer sits at the bolted joint between the front propshaft and its mating flange,...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Front Axle Housing Oil Seal seats in the front axle case where the drive shaft passes through the housing to the hub. It runs against the rotating...

Latch hood, bonnet, RH and LH, with sensor

Bolt with an external Torx head, M12 x 35 mm. Used to secure rear brake components at the disc and calliper mountings, and rear suspension fixings...

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

Oil Drain Plug for the engine oil pan (sump). Threaded into the base of the oil pan, it seals the oil drain point and is removed to drain the engi...

Magnetic Oil Drain Plug for the engine oil sump on the 2.0L Ingenium (AJ200/AJ20) four-cylinder petrol and diesel engines. The plug seals the drai...

Suspension Arm Nut - M16 flanged nut used on the rear suspension. It secures the lateral and lower arm pivot bolts where they pass through the sus...

Pinion Oil Seal for the rear differential, running on the drive pinion shaft. The seal sits where the pinion shaft enters the differential housing...

Exhaust Gas Temperature Sensor measures the temperature of the exhaust stream within the diesel exhaust and emissions system. It reports to the en...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Bolt is a threaded fastener used across several assemblies, including door latch mechanisms, front seat bases and anti-lock braking system mounting...

Bolt

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Window Control Switch for the driver's door, in the double configuration. The switch is mounted in the driver's door armrest and operates the elec...

Idler Pulley for the auxiliary drive belt, 70mm diameter, positioned within the front-end accessory drive system. The pulley guides and stabilises...

Screw - a fastener used to secure exterior body panels and trim, including body mouldings, front and rear bumper assemblies, radiator grille panels...

Key Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...

Tow Slider - Adjustable Saddle Type for the Dixon Bate adjustable tow bracket system. This is the vertically sliding saddle piece in the Dixon Bat...

Towing Jaw rated to 3.5 tonnes, part of the towing/pintle hitch assembly. It provides the jaw coupling for trailer and recovery towing, mounting t...

Tow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Screw - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...

Wheel Hub Assembly for the front and rear axle knuckle assembly. This wheel hub assembly mounts to the steering or rear knuckle and houses the whe...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Valve - Control

Front Suspension Bolt - a mounting bolt used in the front suspension assembly, at the suspension arm and knuckle/hub mountings. It secures the joi...

Timing Chain Kit for the Ingenium 2.0L 4-cylinder engine, covering the complete timing chain system. The Ingenium AJ200 engine uses a dual-chain a...

Plastic Washer - a plastic washer used at the radiator cowl (fan shroud) mounting in the cooling system. It sits under the fixing that secures the...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Thermostat Seal for the thermostat housing on AJ200/AJ20 series petrol and diesel engines. It seals the thermostat housing joint within the cooling...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...

Cylinder Head Gasket for the 5.0L V8 AJ133 petrol engine. The gasket seals the joint between a cylinder head and the engine block, containing comb...

Oil Cooler Gasket seals the oil cooler within the oil cooler and filter housing assembly. It maintains the oil-tight joint between the cooler and ...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...