Land Rover Defender Parts

O-Ring seal for the automatic transmission oil cooler circuit (ZF 8-speed, 8HP). The O-ring seals a connection in the transmission fluid cooling c...

Coolant Hose carries engine coolant between the thermostat housing and the engine on the supercharged 3.0L V6 and 5.0L V8 petrol engines. It runs f...

Water Pump Gasket for the coolant pump on 5.0L V8 (AJ133) and 3.0L supercharged V6 petrol engines. The gasket seals the joint between the water pu...

Drain Plug Sealing Washer seals the M18 oil drain and filler plug on the transfer case. The washer deforms as the plug is tightened to form a leak...

Camshaft Position Sensor for the 2.2L turbo-diesel engine. The sensor monitors the position of the camshaft and signals the engine control unit, w...

Camshaft Position Sensor for the 2.2L turbo-diesel engine. The sensor monitors the position of the camshaft and signals the engine control unit, w...

Anti-Roll Bar Link - connects the rear anti-roll (stabilizer) bar to the suspension on the left-hand side. This drop link transfers body-roll load...

Gasket - Throttle

Throttle Housing Gasket - seals the throttle body to the intake manifold. Forms the air-tight joint between the electronic throttle housing and th...

Degas Hose for the engine cooling system's degassing circuit. The hose routes coolant and entrained air from the engine and radiator to the degas (...

Fuel Injector Refit Kit - the seals and retainer required when removing and refitting a fuel injector on 3.0L V6 and 5.0L V8 supercharged petrol en...

Ignition Coil for V6 and V8 petrol engines, mounted directly on the spark plug in a coil-on-plug arrangement. The coil steps up the battery supply...

Hex Head Bolt and Washer - a hexagon-head bolt supplied with a washer. A general-purpose fixing used at multiple mounting locations, including the...

Ignition Coil for V6 and V8 petrol engines, mounted directly on the spark plug in a coil-on-plug arrangement. The coil steps up the battery supply...

Coolant Hose - throttle body heater outlet hose within the engine cooling circuit. The hose routes engine coolant from the throttle body heater ou...

Engine Temperature Sensor monitors coolant temperature within the engine cooling circuit. It reports coolant temperature to the engine control mod...

Connecting Rod Bearing Set supplies the big-end bearing shells that run between the connecting rods and the crankshaft crankpins. Machined 0.020in...

Idler Pulley - a drive belt idler in the front-end accessory drive (serpentine belt) system. The idler pulley routes and guides the multi-rib driv...

Idler Pulley for the secondary drive belt circuit on supercharged petrol engines. The idler is a freely-rotating, sealed-bearing pulley that guide...

EGR Cooler Gasket seals the mounting joint between the EGR cooler and the exhaust gas recirculation circuit on the 2.2L Puma diesel engine. It mai...

Heater Hose - a coolant hose in the heating and ventilation (HVAC) circuit, running between the heater matrix and the engine water pump. It return...

Connecting Rod Bearing Set supplies the big-end bearing shells that run between the connecting rods and the crankshaft crankpins. Machined 0.010in...

Fuel Injector Grommet - a sealing grommet that locates and retains a fuel injector where it passes through the cylinder head cover. It seals aroun...

Heater Hose - a coolant hose within the heating and ventilation (HVAC) circuit. It carries engine coolant between the cooling system and the heate...

Degas Hose for the engine cooling system's degassing circuit. The hose routes coolant and entrained air from the engine and radiator to the degas (...

Fuel Injector Refit Kit - the seals and retainer required when removing and refitting a fuel injector on 3.0L V6 and 5.0L V8 supercharged petrol en...

Fuel Injector Refit Kit - the seals and retainer required when removing and refitting a fuel injector on 3.0L V6 and 5.0L V8 supercharged petrol en...

High Pressure Fuel Pump Tappet drives the engine-mounted high-pressure fuel pump from the camshaft. The tappet acts as the cam follower, riding on...

Bolt is a threaded fastener used within the chassis and suspension assemblies. It secures mounting points across suspension, stabilizer bar and re...

High Pressure Fuel Pump Tappet drives the engine-mounted high-pressure fuel pump from the camshaft. The tappet acts as the cam follower, riding on...

Idler Pulley for the secondary drive belt circuit on supercharged petrol engines. The idler is a freely-rotating, sealed-bearing pulley that guide...

Accessory Drive Belt from the front-end accessory drive. The primary serpentine belt driven by the crankshaft pulley to turn the engine ancillarie...

Coolant Hose carries engine coolant through the cooling circuit, connecting the components that circulate coolant to and from the engine. Moulded ...

Coolant Hose carries engine coolant through the cooling circuit, connecting the components that circulate coolant to and from the engine. Moulded ...

Flanged Nut for the front suspension arm mountings. The integral flange spreads the clamp load across the joint face and helps the nut resist loos...

Bolt for the suspension mountings. Secures front and rear suspension arms, struts and springs at their attachment points under suspension loads.

EGR Gasket for the exhaust gas recirculation (EGR) system. Seals the flanged joint between the EGR valve and its mating pipework, containing recir...

Exhaust Manifold Bolt secures the exhaust manifold to the cylinder head. For 3.0L supercharged V6 and 5.0L V8 petrol applications.

O-Ring for the variable valve timing (VVT) solenoid. Seals the VVT solenoid where it locates into the cylinder head, retaining oil pressure to the...

Water Outlet Tube carries coolant between the water pump and the thermostat housing within the engine cooling circuit. For 3.0L supercharged V6 an...

Water Outlet Tube carries coolant between the water pump and the thermostat housing within the engine cooling circuit. For 3.0L supercharged V6 an...

Brake Caliper Mounting Bolt for the front brake assembly, securing the caliper to its mounting on the hub carrier. This high-tensile fastener is t...

Bolt - front brake caliper mounting bolt. The bolt secures the front brake caliper to the hub carrier, clamping the caliper against its mounting f...

Retaining Clip - a push-fit fastener used to secure exterior and interior trim mouldings and finishers to the body. The clip pushes into a locatin...

Brake Pads

Timing Chain Lubricating Oil Jet for the timing drive of the 5.0L V8 petrol engine (AJ133, naturally aspirated and supercharged). The jet feeds pr...