Land Rover Defender Parts

Bleed Screw in red anodised aluminium, fitted at the bleed point of the radiator hose circuit on the Td5 2.5L 5-Cylinder Turbo Diesel. The screw c...

Hose Clip - spring-band clip from the charge-air (intercooler) ducting of the Td5 2.5L 5-Cylinder Turbo Diesel. The clip secures a flexible interc...

Silicone Turbo and Intercooler Hose Kit for the 2.2L TD4 turbo diesel charge-air circuit, covering the hose runs between the turbocharger, the inte...

Hose Clip for small-bore hoses in the engine bay. On the Td5 2.5L five-cylinder turbo diesel it retains the cam cover breather valve hose, keeping...

Crankshaft Gear for the timing drive of the 2.2L and 2.4L Puma diesel engines. Mounted on the nose of the crankshaft, this sprocket drives the tim...

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Engine Mount Insulator for the engine and transmission mounting system. The insulator is the rubber-and-metal mount that supports the powertrain o...

O-Ring for the diesel fuel injection system. It forms a fuel-tight seal at the injector, within the fuel injectors and pipes assembly. Supplied as...

Pressure Relief Valve regulates pressure in the fuel injector leak-off (return) circuit. Fitted to the 2.4 litre Duratorq TDCi (Puma) diesel engin...

Pressure Relief Valve for the fuel injector leak-off circuit on the 2.4L Duratorq TDCi HPCR diesel engine. It maintains the correct residual press...

Air Inlet Connection for the exhaust gas recirculation (EGR) system on the Puma TDCi diesel engine. This connection forms part of the EGR pipework...

Anti-Roll Bar Link connects the front anti-roll bar to the suspension, part of the front stabilizer bar assembly. It transfers movement between th...

Pressure Relief Valve regulates pressure in the fuel injector leak-off (return) circuit. Fitted to the 2.4 litre Duratorq TDCi (Puma) diesel engin...

Split Pin used throughout the handbrake and gearchange linkages. The pin passes through a clevis pin or castle nut and its legs are spread on asse...

Piston Ring Set for the 5.0L V8 AJ133 petrol engine, supplied at standard bore size. The ring pack seals the combustion chamber against the cylind...

Piston ring set for the 5.0L V8 AJ133 petrol engine, both naturally aspirated and supercharged, in +0.50 mm oversize. One set covers a single pist...

Piston Ring Set for the 5.0L V8 AJ133 petrol engine, supplied at standard bore size. The ring pack seals the combustion chamber against the cylind...

Hub Bearing

Bearing - Wheel Hub

Wheel Bearing Kit

Vent Hose for the engine cooling and cabin heating circuit. This hose routes coolant at the heater matrix outlet, carrying it back into the coolin...

Brake Disc Retaining Screw that locates the brake disc against the wheel hub flange, holding the disc square and in position while the caliper and ...

Folding Side Step fits beneath the side doors as a step aid for entry and exit. The step folds upward when not in use to preserve ground clearance...

Seal

Drive Belt Idler Pulley - a non-driven guide pulley in the accessory drive belt system of the 3.0L AJ20P6 six-cylinder petrol engine. The idler gu...

Stainless steel braided brake hose kit, four-line, +2" extended length, for the ABS-equipped hydraulic layout. The flexible hoses carry hydraulic p...

Rear Quadrant Plate - a chequer plate panel for the quadrant section of the station wagon rear body side, within the exterior body protection assem...

Battery earth cable, 1170 mm long - the main negative lead of the starting and charging circuit. It connects the battery negative terminal to the ...

Ignition coil for the distributor ignition system on V8 petrol engines. Steps the low-tension supply up to the high-tension voltage required at th...

Moulding - Front Wheel Arch

Ignition coil for the distributor ignition system on V8 petrol engines. Steps the low-tension supply up to the high-tension voltage required at th...

Breather Tube forming part of the crankcase ventilation circuit on the 5.0L V8 petrol engine (AJ133). It carries crankcase blow-by gases from the ...

Retaining Clip is a fastening clip used in the radiator grille and front bumper assembly. It secures the grille and front bumper trim components t...

Fusible Link - in-line fusible link in the air conditioning wiring harness. It is spliced into the supply feed to the air conditioning circuit and...

Clip - retaining clip for the radiator grille and front bumper assembly. It secures the grille and bumper components to their mountings.

Battery Cable - positive lead within the battery and starting circuit. It carries the main positive supply from the battery terminal to the starte...

Number Plate Plinth - rear registration plate plinth, part of the rear body exterior fittings. It mounts to the rear body panel and provides the f...

Brake Disc Splash Shield - Rear - RH - Galv is the right-hand rear brake disc splash shield, the backing plate mounted behind the disc on the rear ...

Brake Disc - Rear - Wavy CDG is a rear brake disc with a wavy (scalloped) outer profile and cross-drilled, grooved friction faces. It replaces the ...

Brake Disc Splash Shield - Rear - LH - Galv is the left-hand rear brake disc splash shield, the backing plate mounted behind the disc on the rear a...

Wiring Harness - link harness for the reverse lamp switch, within the rear lighting circuit. It connects the reverse lamp switch into the main rea...

Brake Disc - Rear - Solid is a solid (non-vented) disc forming the friction surface of the rear disc brake assembly. The disc mounts to the rear h...

Brake Disc - Rear - Solid - Coated is a solid (non-vented) disc forming the friction surface of the rear disc brake assembly, supplied with a prote...

Front Brake Disc - Solid, Cross-Drilled and Grooved. Solid (non-ventilated) front brake disc with a cross-drilled and grooved friction face. The d...

Wing Top Vent Grilles - the heater air intake vents mounted in the top face of the front wings, supplied as a matched left and right pair. They ar...

Brake Disc Shield Bracket - Rear - mounting bracket in the rear brake assembly. It locates and supports the rear brake disc splash shield, holding...