Land Rover Defender Parts

Diesel Fuel Filter - replaceable cartridge filter element for the fuel supply circuit on 200 TDi and 300 TDi diesel engines. The element sits in t...

Brake Master Cylinder Repair Kit for the dual-line (split-circuit) braking system with direct-acting servo. This is a seal/overhaul kit that recon...

Sump Plug seals the drain aperture at the base of the engine sump, retaining the engine oil and providing the drain point for an oil change. Remov...

Cylinder Block Drain Tap threads into the coolant jacket of the cylinder block, providing a controlled drain point for the engine cooling system. ...

Exhaust Manifold bolts to the exhaust ports on the cylinder head and collects the exhaust gases from the cylinders into a single outlet feeding the...

Brake Drum - 11 in - Large Wheel Studs is a cast iron drum for the drum brake assemblies of Series 3 and Defender models. The drum measures 11 inc...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Chassis Harness Grommet - black rubber grommet for the chassis wiring harness, 6 x 33.5mm. Fitted where the wiring harness passes through a chassi...

Wheel Centre Cap - a black alloy-wheel centre cap carrying the Land Rover oval in green and silver. It presses into the centre bore of an alloy wh...

Instrument Panel Bulb, rated 12V 2W with a BA7s bayonet base (type 281), for the instrument cluster lighting circuit. It provides the internal ill...

Brake Pad Spring Kit retains the front brake pads within the caliper, holding them against rattle and locating them on the pad retaining pins. For...

Folding Side Step mounts beneath the side door sill to provide a sprung step that aids entry and exit, folding up against the body when not in use ...

Wiper Blade, 315mm, for the windscreen and rear screen wash-wipe system. The blade carries the wiping element that sweeps across the glass to clea...

Bodyside Seal for the lower edge of the rear upper body section, sealing the joint between the upper body structure and the lower body on the rear ...

Rear door seal RH 110

Front axle drive flange designed to connect the drive shaft to the wheel hub assembly. The flange transmits rotational force from the half shaft ...

Depression control valve assembly TD5 and 2L Freelander

Brake Caliper Carrier Bolt secures the brake caliper carrier (mounting bracket) to the axle, providing the clamping force that holds the caliper as...

Camshaft Cover Grommet sealing the camshaft cover to the cylinder head on the Td5 2.5L five-cylinder turbo diesel engine. The grommet forms a stat...

Centre Exhaust Box (centre silencer), part of the exhaust system. Mounted in the centre section of the exhaust line between the front pipe and the...

Decoke Head Gasket Set for the 2.25L 4-cylinder diesel engine - the top-end gasket set used for a full decarbonising (decoke) job or when removing ...

Engine Bottom-End Gasket Set for the 2.25L 4-cylinder petrol engine, supplying the lower-engine gaskets and seals used during a bottom-end overhaul...

Heater Blower Duct Seal for diesel applications, fitted in the heater air intake. This foam seal sits between the air inlet duct and the heater blo...

Driver's door lock actuator and switch CDL

Shim .003" for swivel pins

Track Rod End Boot for the steering track rod end ball joint. This rubber boot fits over the track rod end housing, sealing the ball joint against...

This camshaft sprocket is designed for Land Rover V8 engines, providing precise timing and reliable performance.

Glass Fuse rated at 10A, a cartridge-type fuse used in the vehicle electrical system. The fuse seats in the fuse box or an inline fuse holder and ...

Head Gasket Set - 2.25 Petrol - Composite is a top-end (de-coke) gasket set for resealing the cylinder head assembly of the 2.25-litre petrol engin...

Air filter element Puma TD4 Def.

Hex Nut with a 7/8" UNF (Unified National Fine) thread, used on the power steering box assembly. This large six-sided fastener threads onto a matc...

Bolt for the suspension mounting. A 7/16" UNF thread bolt of 6.5" length, used at the upper suspension mounting to secure the shock absorber and sp...

Fuel Connector Block Gasket for the Td5 2.5L five-cylinder turbo diesel engine, sealing the fuel connector block to the engine within the fuel pres...

Air flow meter TD5 OEM VDO /Delphi

Brake Master Cylinder within the Master Cylinder & Servo assembly, fitted to non-ABS braking configurations. This hydraulic component converts...

Breather O-Ring for the 2.5L diesel engine (NA Diesel, 200 TDi and 300 TDi), used in the crankcase ventilation system. It seals the cyclone breath...

Oil Separator Drain Hose for the 300 Tdi 2.5L 4-cylinder turbo diesel engine, part of the crankcase ventilation system. It returns the oil collect...

Brake Disc, front, vented. Part of the front braking system. The disc mounts to the front wheel hub and rotates with the wheel; the brake caliper ...

Swivel Pin Housing Thrust Washer for the front axle swivel pin assembly. Installed within the swivel pin housing between the pin head and the hous...

LT230 Transfer Box Bottom Cover Gasket, sealing the main casing bottom cover of the LT230 two-speed transfer box. Fits the main casing bottom cove...

Swivel Pin Housing Shim - 0.25mm (0.010") for the front axle swivel pin housing assembly. This precision shim is fitted between the swivel pin hou...

Swivel Pin Housing Shim - 0.075mm (0.003") for the front axle swivel pin housing assembly. This precision shim is fitted between the swivel pin ho...

Seat Belt Assembly - Front - LH - complete front left-hand seat belt assembly in Ash Grey. This active (inertia reel) assembly comprises the retra...

Electronic Distributor - complete distributor assembly for the 4-cylinder petrol engine, supplied with the electronic ignition conversion already f...

Injector O-Ring for the 2.5L Td5 5-Cylinder Turbo Diesel fuel injection system. This O-ring seats in the groove on the injector body at the cylind...

O-Ring for the engine cooling system thermostat housing. This sealing ring fits the drain or filler plug on the thermostat housing, providing a le...

Water Pump Gasket for the engine cooling system, sealing the water pump mounting face against the engine block. Fitted to the 11L engine block ver...

Wiper Arm The arm assembly within the front windscreen wiper mechanism, for left-hand drive configuration. It mounts onto the wiper motor spindle ...