Land Rover Defender Parts

Hub Oil Seal - Inner for the front and rear wheel hubs, seating around the stub axle. The seal runs on the stub axle to retain hub lubricant and e...

Anti-Roll Bar Strap Bracket for the front suspension assembly. Provides the mounting point for the anti-roll bar strap on the axle casing. The bra...

Rear Wing Protector in aluminium chequer plate, guarding the rear wing top and corner - one of the most exposed panels on the body. Fits over the ...

Starter Motor

Caliper - Piston

Windscreen Washer Reservoir

Chequered Sills 90 - Pair

Stud

Brushed Stainless Steel Door Thresher E

Brake Pipe Assembly for the left-hand side of the hydraulic brake circuit. This rigid, pre-formed pipe carries pressurised brake fluid between the ...

Fuel Pipe Union Nut for the fuel delivery line. This female threaded nut draws a fuel pipe up to its mating union, clamping the pipe's flared or c...

Fir Tree Clip - a push-fit fastener that secures the door casing (interior door trim panel) to the door. The ribbed, tapered fir-tree stem pushes ...

HD Rear Bumper

Door Hinge Kit - Front - front door hinge and pin set with fixings, forming part of the door mounting hardware. Each hinge bolts to the body pilla...

Exhaust Manifold Stud secures the exhaust manifold to the cylinder head, part of the exhaust manifold mounting hardware. This is an M10 stud, thre...

Brake Pipe Clip - Double secures and routes rigid hydraulic brake pipes within the braking system. This double clip retains two brake pipes at a s...

Heater Blower Motor and Fan Assembly - the powered fan unit of the cabin heating, ventilation and demisting system. The electric motor drives the ...

Door Latch Striker Screw - fixing screw that secures the door latch striker to the body pillar. The striker is the catch the door latch engages to ...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Power Steering Pump - belt-driven hydraulic pump forming the pressure source of the power assisted steering circuit. Mounted on the engine and dri...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Rear Axle Half Shaft - RH, Heavy Duty, part of the disc-braked Salisbury rear axle assembly. The right-hand halfshaft transmits drive from the dif...

Coolant Temperature Transmitter - Black mounted at the thermostat housing, supplying the coolant temperature signal to the instrument cluster tempe...

Bolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...

Seal - Oil Pump

Decoke Gasket Set for the 3.9/4.0/4.2L Rover V8 EFI petrol engine. This is the set of gaskets and seals used to reseal the top end of the engine - ...

Head Gasket

Air Intake Hose for the 2.25 litre diesel engine, forming part of the air induction system between the air cleaner and the intake manifold. It car...

Clutch Kit is a matched three-piece clutch assembly for the 3.5L V8 petrol engine with manual transmission. The kit renews the complete clutch as ...

Suspension Kit - a heavy-duty coil spring and shock absorber set giving a +40mm raised ride height on the front and rear axles. The kit contains h...

Driving Member (axle drive flange) for the front and rear hub assemblies. It bolts to the outer face of the hub and engages the splined end of the ...

Stainless Steel Rear Door Hinge for the rear end (tailgate) door, supplied as a replacement for the original hinge which corrodes and seizes over t...

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...

Horn - High Note

Front Axle Drive Shaft transmits drive from the front differential to the right-hand wheel hub, forming part of the front axle drive shaft and hub ...

Belt

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Bonnet Release Cable connects the cabin-mounted release lever to the bonnet latch as part of the bonnet locking mechanism. Pulling the interior le...

Caliper - Assembly - Front Brakes - RH

Wastegate Modulator for the turbocharger boost control system. This electro-pneumatic solenoid valve is controlled by the engine ECU and regulates...

Front Grille Panel sits within the front body panel assembly, ahead of the radiator and intercooler. It admits airflow to the engine cooling pack w...

Stop/Tail Bulb - 12V 21W - Twin Pack (trade reference 380). This pack contains two BAY15d dual-filament bayonet bulbs rated 12V 5/21W, suitable fo...

Coolant Expansion Tank in black, part of the engine cooling system. The tank serves as the system's pressurised reservoir and fill point, accommod...

Cylinder Head Bolt securing the cylinder head to the cylinder block and clamping the head gasket joint. It maintains the clamping force that seals...

Cam Cover Sealing Washer Seals a camshaft cover retaining bolt on the 300 TDi 2.5L turbo diesel engine. Fitted beneath the head of the cam (rocker...

Door Latch - Rear Side - RH

Sealing Ring for the 2.4L Duratorq TDCi diesel, sealing the thermostat into its metal housing on the engine. It forms the coolant-tight seal betwe...