Land Rover Defender Parts

Coupling - Viscous Borgwarner

Taper Roller Bearing - outer pinion bearing in the differential final drive assembly. The drive pinion is carried on a pair of opposed taper rolle...

Front Cover Gasket for the 2.4L Duratorq TDCi (Puma) diesel engine, also used on the 2.2L Puma TDCi. It seals the joint between the engine front (t...

Flanged Nyloc Nut, M10, a multi-purpose locking fastener used across the chassis and suspension. The nylon insert resists loosening under vibratio...

Fuel Stop Solenoid for the 200 Tdi and 300 Tdi 2.5L turbo diesel engine, mounted on the fuel injection pump. Held open while energised through the...

Seat Base Cover in grey vinyl, for the front outer seat cushion - driver or outer passenger side. Replaces the worn or damaged trim cover on the s...

Inhibitor Switch

Swivel Joint Washer located within the Swivel Pin Housing Assembly, sealing the interface between the swivel housing flange and the axle beam face....

Exhaust Manifold Gasket for the 200 TDi diesel engine, sealing the joint between the exhaust manifold and the cylinder head. It seals each exhaust...

Kit - Floor Contour Mat

Rear Door Glass - the glass assembly for the rear end (tail) door. It incorporates a heated element for demisting the rear window and an integrate...

Wiper Drum Adaptor - splined adaptor used in the windscreen wiper system to connect the wiper arm to the splined wiper spindle. The adaptor seats ...

Layshaft Bearing - taper roller bearing supporting the layshaft in the R380 5-speed manual gearbox. The bearing carries the countershaft (layshaft...

Intercooler for the turbocharger charge-air circuit on Td5 and Puma TDCi diesel engines. Mounted in the airflow ahead of the radiator, the interco...

Crankshaft Oil Seal - Front seals the nose of the crankshaft where it passes through the timing cover on the Td5 2.5L 5-cylinder turbo diesel engin...

Camshaft Seal - Rear

Rear Brake Caliper Piston for the rear disc brake caliper. The piston runs in the caliper bore behind the square-section piston seal and dust boot,...

Panel - Wing - Front

Swivel Pin Housing Kit rebuilds the upper pivot of the front axle swivel housing, where the steering knuckle articulates on the axle. This is the v...

Front Right-Hand Brake Pipe for the hydraulic braking circuit, non-ABS systems. This pre-formed rigid steel pipe carries brake fluid through the f...

Piston Assembly - +0.020" Oversize for the 300Tdi 2.5L 4-Cylinder Turbo Diesel engine. This piston is machined to a diameter 0.020" (approximately...

Fuel Injector for the 2.5L 300TDi 4-cylinder turbo diesel engine. This direct injection fuel injector delivers metered, atomised fuel into the pre...

Oil Seal for the R380 manual gearbox extension case (rear/tail housing). It seals the output shaft where it exits the extension housing, retaining...

Bolt - Flanged Hex

Clutch Plate - 242mm

Connecting Rod Bearing Set for the 2.5-litre 4-cylinder engine, including the 200 TDi and 300 TDi diesels. These are the replaceable big-end shell ...

Engine Mounting Bracket - 3.5L V8

Oil Seal for the R380 manual gearbox extension case (rear/tail housing). It seals the output shaft where it exits the extension housing, retaining...

Water Pump is the engine-driven mechanical pump that circulates coolant through the cylinder block, cylinder heads and radiator to maintain engine ...

Raised Air Intake Fitting Kit - fitting hardware for the Terrafirma raised air intake, supplied separately from the intake itself. The raised air ...

Fitting Kit for Pacet Fan

Rear Stub Axle for the Salisbury rear axle assembly. The stub axle bolts to the outer end of the axle casing and forms the fixed spindle on which ...

Anti-Roll Bar Bush in the suspension anti-roll bar mounting, locating the stabiliser bar against the chassis. This polyurethane bush cradles the a...

Rear Light Lens for the rear stop and tail lamp. The red lens fits over the lamp body to cover the stop and tail bulb, transmitting the brake ligh...

Alternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...

Exhaust Valve Guide is pressed into the cylinder head and supports the exhaust valve stem, keeping it accurately centred as the valve opens and clo...

Clutch Slave Cylinder for the hydraulic clutch release system on Defender and Discovery 2 models fitted with the R380 manual gearbox. Mounted on t...

Heater Blower Duct Seal for diesel applications, fitted in the heater air intake. This foam seal sits between the air inlet duct and the heater blo...

ABS Wheel Speed Sensor - front sensor for the four-wheel anti-lock braking system. The sensor mounts in the front axle housing with its pole piece...

Retaining Clip for the output shaft oil seal on the MT82 6-speed manual gearbox. The clip locates and secures the oil seal within the gearbox hous...

Main Bearing Set 020 (Lc)

Idler Tensioner Pulley for the auxiliary (serpentine) drive belt system. Mounted on the automatic belt tensioner arm, the pulley bears against the ...

Rear Differential Drive Flange Kit for the Land Rover (Rover-type) rear axle. The drive flange mounts to the differential pinion and provides the ...

Engine Overhaul Gasket & Seal Set for the 200TDi diesel engine, covering the bottom end of the engine. This set provides the gaskets and seals...

Wheel Bearing Kit - a complete single-hub kit containing the bearings, seal and fixings to rebuild one wheel hub, suitable for either a front or a ...

Manifold Stud - M8 x 36 mm - for the Td5 2.5L 5-cylinder turbo diesel engine. The stud threads into the cylinder head to locate the manifold flang...