Land Rover Defender Parts

Coolant Hose connecting the coolant expansion tank to the radiator within the engine cooling circuit. This moulded hose carries coolant between th...

Nyloc Nut with an M16 thread - a nylon-insert locking nut used on heavily loaded suspension and driveline fixings. A nylon collar set into the top...

Brake Pipe Clip (double) for ABS-equipped braking systems, used to route and secure rigid brake pipes. The double form holds two brake pipes side ...

Fuel Filler Hose in the fuel tank filler assembly, connecting the filler neck to the tank. It carries fuel from the filler neck into the tank duri...

Coil Spring for the right-hand side of the coil-sprung suspension, identified by its red/blue paint marking which denotes the spring's load rating....

Spring Retainer secures the upper outer mounting of the rear coil spring and damper within the rear suspension assembly. It clamps the top of the ...

Exhaust Spacer Tube is a short pipe section within the exhaust system. It spaces and connects adjacent exhaust sections at a flanged joint, settin...

Brake T-Piece - Metric is a three-way junction in the brake hydraulic circuit. It joins three brake pipes at a single union, typically distributin...

Seal

Front Mudflap Bracket for the left-hand front mudflap. The bracket mounts behind the front wheel and holds the mudflap in position, locating it to...

Heater Blower Seal sealing the joint between the intake grille and the heater duct, for diesel applications. Fitted in the heater air intake, it cl...

Upper Rear Door Hinge for the rear end (tailgate) door, part of the body and door assembly. It is the upper of the two hinges that carry the side-...

Rear Stop/Tail Lamp - LED - LED combined stop and tail lamp with a red lens, supplied as a complete sealed unit to replace the standard rear stop/t...

Drive Belt Tensioner maintains correct tension on the auxiliary drive belt of the 2.4 and 2.2 TDCi engines. The spring-loaded tensioner pulley bea...

Oil Separator Drain Hose for the 300 Tdi 2.5L 4-cylinder turbo diesel engine, part of the crankcase ventilation system. It returns the oil collect...

Swivel Housing Kit for the front axle swivel assembly, for vehicles fitted with ABS. The kit covers one side of the axle. It rebuilds the swivel j...

Flanged Nyloc Nut, M10, a multi-purpose locking fastener used across the chassis and suspension. The nylon insert resists loosening under vibratio...

Flanged Bolt, M10 x 30 mm. A metric bolt with an integral flange beneath the hexagon head that spreads clamping load over a wider area and helps re...

Front seat belt LH

Camshaft Oil Seal seals the camshaft on the 2.5L 4-cylinder diesel engines, including the 200TDi. Fitted at the front of the engine where the cams...

Timing Chain for the 2.25L four-cylinder engine, part of the timing drive assembly. Drives the camshaft from the crankshaft sprocket, holding valv...

Air Filter Element is the replaceable filtration element of the engine air intake system. It seats inside the air cleaner housing and traps dust an...

Timing Cover Plate Gasket sealing the timing gear cover plate on the 300Tdi 2.5L four-cylinder turbo diesel engine. The gasket forms the joint bet...

Injector Sealing Washer seals the base of the fuel injector into the cylinder head on the Td5 2.5L 5-cylinder turbo diesel engine. The washer sits...

Brake Vacuum Pump for the 300 TDi 2.5L turbo-diesel engine, mounted on the engine as part of the brake vacuum circuit. Driven mechanically by the ...

Camshaft Oil Seal - radial oil seal for the 2.5L 300 TDi turbo diesel engine, fitted in the front timing cover within the timing gear assembly. Th...

Glow Plug for the diesel cold-start pre-heating system, threaded into the cylinder head to project into the combustion chamber (or pre-combustion c...

Oil Pump Gasket for the engine lubrication system, sealing the oil pump to its mounting face on the cylinder block. It maintains a leak-free joint...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Headlamp Assembly for the front exterior lighting system, supplied as a pair. Each crystal-style halogen unit mounts in the front lighting housing...

Seat Base Foam Cushion forms the lower outer section of the seat base assembly within the interior seating system. It provides the primary support...

Door Bolt Kit - a stainless steel fixing set for the four side doors (Non-Puma applications). The kit comprises M8 countersunk Allen-head bolts, J...

Corner capping RH 90/110 black MA

Loadspace Mat Retainer for the rear door aperture at the tailboard. The retainer is a profiled strip that clamps the rear door weatherseal and the...

Brake & Clutch Master Cylinder - Combined CV-Type serves both the braking and clutch hydraulic circuits from a single unit. In this CV-type de...

Overhaul kit brake/clutch master cylinder replacement

Front Exhaust Pipe (downpipe) for the 2.25L diesel engine, forming the first section of the exhaust system. The front pipe bolts to the exhaust ma...

Gearbox-Transfer Box Gasket for the LT76 gearbox, sealing the mating joint between the gearbox and the transfer box. The gasket maintains the oil-...

Differential Drive Flange for the Salisbury rear differential. It bolts to the differential pinion shaft and forms the coupling face to which the r...

Core Plug for the V8 petrol cylinder block and inlet manifold. The cup-type plug seals the casting core holes left in the coolant jacket after man...

Tab Washer for the steering drop arm retaining nut on the Adwest steering box. Fitted beneath the drop arm nut on the steering box output shaft, t...

Fitment: All models to 1980 except V8

Heater Hose connects the cylinder head heater outlet into the heater coolant circuit, carrying hot coolant from the engine toward the heater matrix...

Wheel Stud for the axle hub - 16mm pull-in type. Mounts in the hub flange to carry the road wheel, which is clamped by the wheel nut running on th...

Expansion Tank Cap seals the cooling system expansion (header) tank. The plastic cap closes the tank and holds the coolant circuit at its rated pr...

Grommet - a rubber panel grommet providing a sealed, protected pass-through for the choke cable and windscreen washer tubing. Fitted into the pane...

Core Plug for the cylinder head, sealing a core hole left in the casting during manufacture. It closes the opening left by the casting sand core a...

Bulb rated 12V 10W with a BA15S bayonet cap. A single-contact bayonet-fitting (BA15S) bulb for 12-volt circuits. The single-contact cap suits sing...