Land Rover Defender Parts

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Transfer Box Gear - High is the high range gear wheel in the Land Rover Series transfer box assembly, fitting Series vehicles from 1948 to 1984. T...

Stud for use in Land Rover gearbox assembly.

External Circlip - retaining circlip fitted within the LT67 main gearbox. Seats in a shaft groove to axially locate a gear, bearing or spacer on i...

Air Suspension Compressor - AMK-type compressor assembly from the air suspension supply circuit, for vehicles with four-corner air suspension. The...

Coolant Tube forming the primary coolant path between the cylinder block and the water outlet. This aluminium tube carries coolant from the engine...

Water Pump is the engine-driven mechanical pump that circulates coolant through the cylinder block, cylinder heads and radiator to maintain engine ...

Front Brake Disc, 363mm diameter, ventilated construction, supplied singly. The disc runs within the front caliper and provides both the friction ...

Brake Pad Set - Rear - friction pad set for the rear brake discs and calipers assembly, supplied as a complete axle set covering both rear wheels. ...

Oil Filter - the replaceable cartridge element for the engine lubrication circuit, fitted inside the filter housing on the oil pump, cooler and fil...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Coolant Outlet Pipe - Upper - SC

Pump - Water Hepu

Valve - Control

Bolt - a structural fastener used at chassis and front suspension mounting points, including the front cross member and stabiliser bar crossmember,...

M16 Nut for the front suspension arm. Secures a front suspension arm mounting fastener, holding the joint under suspension loads.

Nut - Flag Type

Bolt

Flanged Nut for use in Land Rover assembly applications. The integrated flange acts as a built-in load-spreading face, distributing clamping force ...

Suspension Arm Bolt secures a front suspension arm to its mounting on the chassis/subframe, part of the front suspension arm mounting hardware. Th...

Raised Air Intake relocates the engine's induction intake point from the inner wing up to roof-line height, drawing intake air from above the bonne...

Alloy Expedition Roof Rack for the Land Rover Defender 90. This aluminium alloy roof rack measures 1.8 x 1.4 m and weighs approximately 35 kg. A c...

torx screw and washer, M6x18mm OEM

Steel Wheel - a 20x8 modular steel road wheel finished in satin black, supplied with matching wheel nuts. Rim specification: 20x8 in, ET45 offset,...

Turbocharger Gasket for the 2.0L AJ200D Ingenium four-cylinder diesel, sealing the turbocharger mounting joint against exhaust gas leakage. The ga...

Portable Jump Starter and Air Compressor - a handheld 12V power pack combining a battery jump starter, power bank, tyre inflator and LED work light...

Brake Pad Set - Front - friction pad set for the front brake discs and calipers assembly, supplied as a complete axle set covering both front wheel...

Front Brake Disc - a vented disc from the front brake disc and caliper assembly. The disc is mounted on the front hub behind the road wheel and ro...

Screw and Washer - M5 x 20 is a self-tapping fastener with a captive washer, an M5 thread, 20 mm length and a hex head. It secures body panels, sp...

Defender 90 Scale Model - a 1:76 scale diecast model of the Land Rover Defender 90, finished in Pangea Green. The model reproduces the Defender 90...

External Torx Head Bolt, M8 x 48 mm, for the front propshaft flange. The bolt clamps the front propshaft flange to its mating drive flange. Its ex...

Propshaft Washer for the front propshaft flange connection. The washer sits at the bolted joint between the front propshaft and its mating flange,...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Fuel Tank Sender Unit for the Defender 90 main fuel tank. The sender unit mounts inside the fuel tank and uses a float arm and variable resistor t...

Front Brake Pads Britpartxs

Oil Filter for the engine lubrication system. It removes contaminants from the engine oil as it circulates, protecting the bearings and moving par...

Washer - a sealing washer for the air conditioning system, used at the condenser and compressor refrigerant connections. It seats at the pipe unio...

Spare Wheel Cover is a rigid cover that fits over an externally mounted spare wheel. Moulded in hard plastic with a gloss black finish, it shields...

Synthetic Winch Rope - 10mm x 24m - 10,000 lbs for 4x4 winch recovery. This synthetic fibre winch rope is rated to 10,000 lbs (approx. 4,536 kg) b...

Brake Vacuum Tank for the Land Rover Series III 2.25 Diesel. Fitted in the brake servo vacuum circuit, the tank stores a vacuum reserve to ensure c...

Rocker Shaft Stud for the cylinder head valve train, securing a rocker shaft pedestal to the cylinder head. The stud locates and clamps the rocker...

Pipe Clip used to secure and route pipework such as fuel breather and roll-over anti-spill lines. The clip holds the pipe at a fixed point to prev...

3 man seat Techno Exmoor trim EX4188 EXT006-TC

Halogen Bulb - H4 100/80W (Non-CE). Dual-filament headlight bulb rated 100W high beam and 80W low beam, providing increased light output over the s...

Finger Pull for the side door sliding glass window. The outer grip fitted to the sliding glass pane, used to slide the window open and closed.

Inlet Rocker Bush for the valve gear, forming the bearing surface between the inlet rocker arm and the rocker shaft. The bush locates the inlet ro...

Wheel Chock for securing a stationary vehicle. Placed against a tyre, the wedge-shaped chock prevents the vehicle from rolling when parked on an i...