Land Rover Defender Parts

Fuel Filter for the diesel fuel delivery system, separating dirt, debris and water from the fuel before it reaches the injection pump. Fitted in t...

Oil Filter Rotor is the rotating element of the centrifugal oil filter on the Td5 2.5L 5-cylinder turbo diesel engine. Mounted within the centrifu...

Oil Filter for the engine lubrication system of the 2.25L four-cylinder petrol and diesel engine. The filter traps combustion by-products, metal p...

Swivel Pin Housing Oil Seal - 9mm seal fitted to the front axle swivel housing. It seals the point where the drive shaft enters the swivel housing...

Exhaust Manifold to Turbo Gasket seals the joint between the exhaust manifold outlet and the turbocharger inlet within the exhaust manifold and tur...

Front Cover Oil Seal

Fuel Injector Harness for the Td5 fuel injection system, carrying the electrical connection between the engine wiring loom and the electronic unit ...

Drive flange for the front axle drive shaft hub assembly. This component provides the splined connection between the drive shaft and the wheel hub,...

Fuel Lift Pump for the low-pressure fuel supply circuit of the 2.5L 300TDi turbo diesel engine. This engine-mounted mechanical diaphragm pump draw...

Fuel Tank Sender Locking Ring for the fuel tank sender unit assembly. This ring secures the fuel level sender unit in position within the fuel tan...

Engine Mounting - bonded rubber-to-metal mount within the engine mounting assembly of 4-cylinder Land Rover engines. It locates between the engine...

Radiator Grille Panel - front grille panel forming the cooling-air intake aperture of the front-end body assembly. It mounts ahead of the radiator...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Flasher lamp OEM WIPAC fits front and rear

Glass Fuse - 35A cartridge fuse for the electrical system. A glass-bodied fuse rated at 35A that protects a wiring circuit against overcurrent; th...

Spring Retainer Ring for the front coil spring on the suspension. The ring secures the coil spring to its seat, holding the spring captive so that...

Exhaust Manifold Gasket for the Td5 2.5L 5-cylinder turbo diesel engine. Seals the joint between the exhaust manifold and the cylinder head, preve...

Master Lighting Switch - column-mounted master switch controlling the primary exterior lighting circuits. Mounted within the steering column switc...

Front Door Seal fitted to the body aperture of the right-hand front door, forming part of the door perimeter sealing system within the body closure...

HT Ignition Lead Set for the 2.25L and 2.5L 4-cylinder petrol ignition system. This set of four high tension leads connects the distributor to eac...

Rear Reflector mounts in the rear lamp area as part of the rear lighting and signalling assembly. A passive retroreflector that returns incident l...

Oil Seal for the swivel pin housing on the front axle, sealing against the polished surface of the swivel ball. The seal seats in the rear face of...

Oil Filter for the Td5 2.5L five-cylinder turbo diesel. Part of the engine lubrication system. The filter is a replaceable cartridge element that ...

Clutch Release Staple is the spring retaining clip that secures the clutch release bearing assembly to the clutch fork, holding the bearing in posi...

Rear Lamp Loom Harness Extension for the exterior lighting circuit. A two-pin extension harness that lengthens the wiring run between the main bod...

Tap screw

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Hub retaining nut

Shock absorber bush (eye), anti roll bar bush

Differential Pinion Oil Seal with a double sealing lip, for the front and rear differentials. It is press-fitted into the differential housing aro...

Windscreen Washer Jet directs washer fluid onto the windscreen as part of the front wash/wipe system. This single jet is bulkhead-mounted and fed ...

Swivel Pin Housing Oil Seal - 9mm seal fitted to the front axle swivel housing. It seals the point where the drive shaft enters the swivel housing...

Rocker Cover Gasket for the 2.5L 300TDi diesel engine, sealing the interface between the rocker cover and the cylinder head. Installed at the top ...

Pinion Seal - Salisbury Axle seals the nose of the pinion shaft at the front of the Salisbury differential housing, where the propshaft coupling fl...

Hylomar Universal Blue is a non-setting gasket jointing compound for use on gaskets and machined metal joint faces in automotive and engineering ap...

Inlet Manifold Gasket for the V8 petrol engine, forming the seal between the central inlet manifold casting and the cylinder head intake faces. It...

Fuel Filler Cap for the fuel tank filler neck, part of the fuel storage and filler assembly. Threads onto the filler neck to seal the fuel tank af...

Universal Joint for the propeller shaft, of the 82mm cap-to-cap type. The universal (cardan) joint connects two sections of the propshaft, transmi...

Fulcrum Bracket and Ball Joint Assembly for the rear A-frame (top link). The bracket forms the apex of the A-frame and bolts to the rear axle; the ...

Lights and Heater Switch - a three-position Lucas-type toggle switch fitted to the dashboard switchgear. It acts as the master control for the exte...

Sealing Washer for diesel fuel injectors, positioned at the injector nozzle seat in the cylinder head to seal against combustion gases around the i...

Radius Arm Bush - Rear, Lower - the compliant mount at the lower link of the rear radius arm, between the arm and its chassis bracket. The rear ra...

Door Grab Handle is the interior pull handle that mounts to the inner face of the door, giving an occupant a hand grip to pull the door closed and ...

Park Switch for the front windscreen wash/wipe system. The park switch sets the rest position of the wiper blades. When the wipers are switched of...

Lock nut 3/8" BSF

Brake Pad Fitting Kit for front brake assemblies running vented discs. The kit supplies the retaining hardware that secures and correctly positions...

Hex Nut - 3/8" UNF - Full is a full-height plain hexagonal nut with a 3/8 inch UNF thread, used as a load-bearing imperial-thread fastener. It is ...

Oil seal designed to retain lubricant and prevent contamination at the stub axle interface. The seal fits into the stub axle and forms a barrier b...