Land Rover Defender Parts

Intercooler Hose Kit - Silicone Blue for the turbocharger and intercooler charge-air circuit on the Td5 2.5L 5-cylinder turbo diesel engine. The k...

Lamp Guard for 95mm NAS round lights fitted to Defender models up to 2016. Designed to protect the larger-diameter 95mm North American Specificati...

Extended Bump Stops are compression-travel limiters that sit between the axle and the chassis to cap suspension up-travel and cushion the axle agai...

Heater To Bulkhead Seal seals the joint between the heater and blower duct and the bulkhead aperture, within the heating and ventilation assembly. ...

LWB voorste ophangpunt van achterste veer LH en RH

Light Guard Set - Rear Hinged rear lamp guard set that protects the rear lamp lenses from stone strike and low-speed impact during off-road use. T...

Mirror Head - 195 mm x 145 mm. The rectangular exterior mirror head that fits the bar-type mirror arm, providing the driver's rearward view along t...

Rocker Shaft for the valvetrain of the Rover V8 petrol engine. The shaft mounts on the cylinder head and carries the rocker arms, transferring pus...

Hex-head bolt, 7/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and soc...

Contact Set (breaker points) for the contact-breaker distributor, of the Ducellier type. The points are opened and closed by the distributor cam t...

Front Sill Panel for the right-hand side of the body, the outer panel running along the lower bodyside below the front door aperture. The sill clo...

Repair kit KIT-POWER ASSISTED STEERING BOX SEAL

Starter Switch for Land Rover Series 1 and Series 2 models (1948-1966). This switch activates the starter solenoid to engage the starter motor whe...

Power Steering Pipe for the power-assisted steering hydraulic circuit, carrying pressurised fluid between the steering pump and the steering box. ...

Brake Master Cylinder Repair Kit - Non-ABS

Fuel Tank Gauge is the fuel level sender unit in the fuel tank assembly. A float-operated sender mounted in the tank, it varies its electrical res...

Drive Belt - the auxiliary (serpentine) drive belt for the 2.4L TDCi (Puma) diesel engine, in the configuration fitted with air conditioning. Driv...

Coolant Hose - Pump To Thermostat is a moulded hose in the engine cooling circuit of the Td5 2.5L 5-cylinder turbo diesel. It connects the coolant...

Radiator Bottom Hose is the lower coolant hose of the engine cooling circuit. It carries cooled coolant from the radiator's lower outlet back to t...

Coolant Hose for the fuel cooler return line. This hose returns coolant from the fuel cooler back to the engine cooling circuit, carrying off the ...

Oil Cooler - the replacement cooler element for the Td5 2.5L 5-cylinder turbo diesel engine oil cooling circuit. This is the finned heat-exchanger...

Nut M16 hex nut for the front anti-roll bar assembly. Secures the front anti-roll bar (stabiliser bar) to its mounting link on the suspension.

Hex Nut is an M8 hexagonal nut, a threaded fastener tightened onto a matching M8 bolt or stud with a standard spanner or socket.

Accelerator Cable for the 300 Tdi 2.5L turbo diesel in left-hand-drive configuration. The cable links the accelerator pedal to the throttle lever ...

Radius Arm Bush Set - polyurethane bushes for the front radius arm mountings at the axle end of the arm, supplied as a set of four in black. The b...

Radiator for the engine cooling system, mounted at the front of the vehicle to dissipate heat from the coolant circulated by the water pump. Air dr...

Radiator Top Hose in the engine cooling circuit, connecting the radiator to the upper coolant pipe. It carries heated coolant from the engine's up...

Fuel Filler Tube forming the neck of the fuel tank filler system. It carries fuel from the filler cap opening down into the tank during refuelling...

Hexagonal Thin Nut, 7/16" UNF, used within the clutch hydraulic circuit at the master cylinder and pipe connections. The reduced-height (thin) pro...

Thin Nut - a reduced-height hex nut with a 5/16" UNF (Unified Fine) thread. The shallow profile suits fastening points with limited clearance and ...

Hex Nut with a 5/16" UNF (Unified National Fine) thread. This six-sided fastener threads onto a matching 5/16" UNF bolt or stud and is tightened w...

Brake Pipe carries hydraulic pressure along the chassis within the braking hydraulic circuit, routing from the front to the rear of the vehicle on ...

Indicator Cancel Ring for the steering column switch assembly. This self-cancel striker ring fits on the steering column beneath the indicator sta...

Exhaust Clamp Plate for the rear section of the exhaust system. This plate clamps the rear silencer to its mounting, securing the assembly and hol...

Accelerator Cable Assembly connects the accelerator pedal to the fuel injection pump throttle lever. It transmits movement of the pedal to the inj...

Shroud clamp

Lower Strut Gaiter for the rear self-levelling suspension unit. This flexible rubber boot fits over the lower ball joint of the self-levelling str...

Exhaust U-Bolt - a U-bolt clamp used to secure a joint in the exhaust system. It retains the exhaust front pipe (downpipe) connection, clamping th...

Front Shock Absorber Turrets - Pair are the tubular mounting towers that locate the upper end of the front dampers in the front suspension. They b...

Saddle Clip for the power steering hydraulic circuit. This saddle-shaped clip clamps a power steering pipe or hose to its mounting point, retaining...

Tank Mounting Spacer - a spacer used in the fuel tank mounting assembly. It sets the correct standoff between the tank and its supporting bracketr...

Hex Nut is a metric M5 hexagonal nut used as a general-purpose threaded fastener across multiple vehicle assemblies. It runs onto a matching M5 ma...

Starter Motor for the Td5 2.5L 5-cylinder turbo diesel engine, operating within the engine electrical starting system. On ignition the solenoid-ac...

Clip Nut spring-steel fastener that provides a captive threaded fixing point on panels and brackets. The nut clips over the edge of a panel or sli...

Air Intake Grille for the cold air induction system. This adaptor grille sits at the cold air intake, drawing cooler outside air into the intake d...

Door Lock Link for the front left-hand door, the operating rod that connects the locking mechanism to the door latch. It transfers movement from t...

Door Latch Striker Spacer - a shim that mounts behind the door latch striker on the body aperture, setting the striker's standoff from the pillar f...

Bonnet Latch Bracket - the top plate that carries the bonnet latch mechanism. It mounts across the front body panel and locates the catch that rece...