Land Rover Defender Parts

Alternator Oil Feed Pipe supplies pressurised engine oil to the vacuum pump integrated at the rear of the alternator, on the Td5 2.5L 5-cylinder tu...

Number Plate Lamp for the rear number plate lighting circuit. This complete lamp assembly mounts at the rear of the vehicle to illuminate the numb...

Spring Washer for use across a wide range of fixings and assembly applications on Land Rover vehicles. This split-ring spring washer is placed ben...

Fuel tank filler hose pipe

Fuel Filler Hose connecting the external fuel filler neck to the fuel tank on the Defender. This rubber hose forms the sealed connection between t...

Fuel Pipe - Filter to Injection Pump for the Defender 300TDi 2.5L diesel (non-EGR). This pipe carries filtered diesel from the fuel filter housing...

Fuel Filter Holder - With Filter for the Defender Puma diesel fuel system. This complete filter assembly mounts in the engine bay fuel circuit and...

Past op 90 2.5L TD5 diesel modellen vanaf (VIN) WA159807 on

Plain Washer in M6 oversize form, with a larger outer diameter than a standard M6 washer. It spreads the clamping load of a bolt head or nut over ...

Plain Washer - metric M8 plain washer for use in general fastening assemblies throughout the vehicle. A standard flat washer used to distribute lo...

Taper Roller Bearing - the mainshaft bearing used in the LT77 and R380 five-speed manual gearboxes, located at the rear of the primary pinion where...

Output Shaft - MT82 6-Speed Manual Gearbox. The output shaft is located at the rear of the MT82 transmission housing and transmits rotational driv...

Spacer 15,1mm Green

Shock Absorber Bush Kit for the mounting points of Terrafirma TS-series shock absorbers. The kit provides the hardware required to replace worn bu...

Return to Centre Steering Damper for installation within the steering linkage assembly. This unit mounts between the axle steering arms and the st...

Spring Retaining Plate - Rear for the rear coil spring seating assembly on Defender 110 and 130. Coil springs can become dislodged from their axle...

Turret Securing Rings - Front are reinforcement rings that fit around the front shock absorber top mount aperture in the inner wing. They distribut...

Sport Front Grille & Headlamp Surround Kit - a front-end exterior styling set that replaces the factory front grille and headlamp surrounds. I...

Rear Coil Spring for the rear suspension, fitting between the axle and the chassis spring seat to support the vehicle and absorb road inputs. This...

Differential Assembly - a reconditioned 4-pin differential unit for the Land Rover-type axle. The differential sits at the centre of the axle, tak...

Roof Access Ladder Rear Assembly is a rear-mounted access ladder with an integrated rear lamp guard. It mounts to the rear bodywork to provide saf...

Locking Wheel Nut Key – Code A. Removal key for code-A locking wheel nuts. The key code is stamped on the original key and cannot be derived from t...

Interior Lamp - courtesy lamp for the passenger compartment. Provides interior illumination as part of the interior lighting circuit, typically sw...

Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...

Brake caliper repair kit front

Taper Roller Bearing - outer pinion bearing in the differential final drive assembly. The drive pinion is carried on a pair of opposed taper rolle...

Filter Kit - 2.2 & 2.4 TDCi for the Land Rover Defender with the Puma TDCi diesel engine. This kit consolidates the main filter and sealing it...

Brake Fluid Reservoir Kit for the brake master cylinder, on vehicles with and without ABS. The kit includes the fluid reservoir, the cap with low ...

Brake Servo Assembly is the vacuum-assisted brake booster in the braking hydraulic system, mounted between the brake pedal linkage and the master c...

Flywheel Bolt, 7/16" UNC x 1" hexagonal head, securing the flywheel to the rear crankshaft flange. Used on V8 petrol engines with manual transmiss...

Hex Bolt - a hexagonal-head bolt with an M6 metric thread and a 12 mm length, manufactured to property class 8.8. Class 8.8 is a medium-carbon ste...

Heater Knob Screw for the heater control assembly. This screw secures a control knob to its spindle on the heater control panel.

Brake Pad Set for the front axle disc brake assembly, for use with solid (non-vented) front discs. The pads locate within the front calipers and cl...

Screw is an M4 x 8mm fastener used in the door mirror assembly, securing components of the interior and exterior mirrors at their mounting points. ...

Shroud Screw - a fixing screw used to secure the steering column shroud and other trim and bracket assemblies. Metric M5 thread with a 40 mm shank...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...

Accelerator Pedal Pad - the moulded rubber cover that fits over the accelerator pedal. It provides a grippable, wear-resistant contact surface for...

Rear suspension panhard rod retaining bolt used in the Radius Arms & Links assembly. This bolt secures the panhard rod to its mounting bracke...

Differential Cover for the Salisbury rear axle. The cover bolts to the rear face of the axle casing, enclosing the crown wheel and differential and...

Drop Arm for the Gemmer recirculating-ball steering box, forming the output lever of the steering linkage. The drop arm mounts on the splined sect...

Nut - 2BA, a small-diameter fastener in the British Association (BA) thread standard. 2BA refers to the No.2 size within the British Association t...

Diesel startermotor military reconditioned EXCHANGE!!

Piston for the 2.5L four-cylinder petrol engine, running in the cylinder bore within the piston, connecting-rod and bearing assembly. Supplied at ...

Rear Wheel Cylinder (Right-Hand) is the hydraulic actuator within the rear drum brake assembly, mounted to the brake backplate. Under pedal pressu...

Lock Washer secures the retaining hardware on the layshaft (countershaft) within the manual gearbox. A tab on the washer is folded against the ret...

Mainshaft Peg is a locating peg fitted to the mainshaft of the LT67 gearbox. It positions and retains its associated component on the gearbox main...

Con Rod Bearing Set - connecting rod big-end bearing shells for the 2.25L four-cylinder engine. The con rod bearings sit between the connecting ro...

Bleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...