Land Rover Defender Parts

Tailgate Hinge for the left-hand side, the lower hinge on which the drop-down tailboard pivots. It carries one side of the tailboard along its low...

Tailgate Hinge for the right-hand side, the lower hinge on which the drop-down tailboard pivots. It carries one side of the tailboard along its lo...

Battery Clamp - the hold-down that secures the battery in its tray. It bears down on the battery to stop it shifting under vibration and off-road m...

Windscreen Glazing Seal - the moulded rubber seal that mounts the windscreen glass into the front bulkhead aperture. It locates and cushions the gl...

Checkstrap cover RH

Heater Blend Knob Screw - retaining screw securing the heater blend control knob to its spindle. Part of the heater control assembly.

Folding Side Step Mat - tread mat fitted to the folding side access step. Provides a non-slip stepping surface for entry and exit at the side doors.

Heater grip OEM

Seat Base Cushion for the inner (centre) position of the 3-person front bench seat assembly. Constructed with a foam core upholstered in black vin...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Sill Panel Stay is a support bracket for the sill (rocker) panel. Forming part of the sill panel assembly, it braces the sill panel to the body st...

Name Plate is the front 'DEFE' lettering decal in black, forming the first half of the DEFENDER name applied to the exterior. It pairs with the 'N...

Front Indicator Lamp - LED is an LED front direction-indicator with a smoked lens, replacing the conventional filament indicator on the front of th...

Front Indicator Lamp forms part of the front direction-indicator lighting, mounted on the front of the vehicle to signal turns and hazard warning. ...

ABS Sensor - Front for Defenders with the 4 wheel anti-lock braking system. This wheel speed sensor mounts at the front axle hub and continuously ...

Body is the right-hand sill channel for the Defender, running along the underside of the door aperture in the body structure. This structural chan...

Locking Plate - the lower tailboard locking plate, mounted to the rear body. Fitted at the lower hinged tailboard, the plate provides the fixed en...

Side Steps - a matched left- and right-hand pair of fixed tubular side runners that bolt to the sill and chassis mounting points, forming a continu...

Engine Sump for the 2.4L and 2.2L Duratorq TDCi Puma diesel engines, bolted to the base of the cylinder block. The sump forms the oil reservoir at...

Gasket OEM

EGR Gasket for the Puma diesel engine. Seals the connection at the Exhaust Gas Recirculation (EGR) cooler, preventing exhaust gas leaks within the ...

Oil Filter is the replaceable element in the engine lubrication circuit, capturing wear particles and combustion contaminants from the oil before i...

Pump Injection Ring

Oil Filler Cap for the engine oil filler neck. Seals the oil filler aperture in the valve cover, preventing oil vapour loss and contamination ingr...

Timing Chain Kit for the Td5 2.5L 5-cylinder turbo diesel engine. The kit includes the timing chain with the camshaft and crankshaft sprockets. Th...

Brake lever kit

Bolt and Washer - an M8 x 25 mm hexagonal-head bolt supplied with a washer. A general-purpose threaded fastener used at various fixing points on t...

DIFFERENTIAL - ASSEMBLY - FRONT AXLE - 24 SPLINE - 4 BOLT FLANGE - D2

Swivel Housing: - Classic Defender 90/110/127/130 upto KA930455 (upto and including 1993 modelyear) (NON-ABS) Axle Code 20L, 21L, 22L, 23L, - Disco...

Breather Adaptor - a threaded fitting in the axle and transfer case ventilation (breather) system. It screws into the axle casing or transfer case...

Retaining Clip for the LT230 transfer box front output shaft. The clip locates on the front output shaft within the LT230 transfer case and retain...

Mainshaft Taper Roller Bearing supports the mainshaft at the 5th/reverse end of the R380 (and LT77) 5-speed manual gearbox. It carries the mainsha...

Bonnet Release Lever for the interior bonnet-release mechanism. Mounted inside the cabin, the lever is pulled to draw the bonnet release cable and...

Flanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...

Spherical Bush for the LT77 and R380 manual gearbox gearchange mechanism. It seats the spherical pivot at the base of the gear lever inside the re...

Clutch Driven Plate for the V8 clutch assembly. It is carried on the gearbox input shaft between the flywheel and the clutch cover (pressure plate)...

Clevis pin

Clevis Pin used to secure a clevis or yoke joint in a mechanical linkage. The pin passes through the yoke and mating rod end and is retained by a ...

Front Cover Gasket for the LT85 5-speed gearbox front cover joint. It seals the front cover against the gearbox case, retaining oil at the input e...

Torsion Spring for the gear lever mechanism of the LT77 and R380 five-speed manual gearboxes. Fitted within the gearchange housing, it supplies th...

Half Shaft Shim is a 1.05mm selective shim used in the front axle drive shaft and hub assembly. It sets the endfloat of the front half shaft drive...

Half Shaft Shim - 0.75mm is a 0.75mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

O-Ring is a sealing ring used within the ZF 4-speed automatic gearbox and the LT230 transfer box. This O-ring seals fluid passages or housing inte...

Flange rear

Swivel Pin Lower Bracket is a retention bracket in the front axle swivel pin housing assembly. Installed at the base of the swivel pin housing, th...

Swivel Pin is the upper pin of the front axle swivel assembly. It bolts to the top of the swivel housing and carries the upper bearing about which ...

Clutch Release Lever Pivot Cap for the clutch release lever pivot pin. One is required per clutch release arm.

striker lock LH for "anti-burst" locks. (lift-up type)