Land Rover Defender Parts

Front Rubber Floor Mats for the driver and passenger footwells, supplied as a matched left- and right-hand pair. Moulded in rubber with a foam bac...

Bonnet Protector Strengthener - chequer plate aluminium panel that mounts over the top surface of the bonnet, shielding the paintwork from stone ch...

Centre Silencer Replacement Pipe occupies the centre section of the exhaust system, replacing the original centre silencer with a free-flowing stra...

Enhance the performance and handling of your Defender 110 with this rear coil spring pair. Designed for heavy-duty use, these yellow springs are pe...

Front Door Skin - aluminium outer panel for the front right-hand door, folded over the door frame to form the visible exterior surface of the door....

Fits Land Rover Defender (1987-2016) Wolf style design for a tough, military-inspired look Sold as a pair for full headlamp protection

Wing Top Protectors are 3mm chequer plate aluminium panels that fit over the top surface of the front wings. Fitted over the wing top sheet metal,...

Swivel Housing Repair Kit renews the front axle steering swivel assembly where the swivel housing has become corroded, worn or is leaking. The swi...

Silicone Turbo & Intercooler Hose Kit - a three-piece set of silicone charge-air hoses for the 300Tdi turbo and intercooler circuit, replacing ...

Waterproof Front Seat Covers for Defender (2007-2016, Puma), in black. This pair of seat covers is designed for the front seats of the Puma-era De...

Front Door Card is the interior trim panel that finishes the inner face of the front door, forming part of the interior door trim assembly. It fit...

Stainless Braided Brake Hose Kit for the flexible sections of the hydraulic braking circuit on non-ABS metric applications. Each hose is built wit...

Spring Retaining Plate for the front coil spring suspension. The plate seats the upper end of the front coil spring against the chassis spring seat...

Diecast Scale Model of the Land Rover Defender 90, finished in Tamer Blue, at 1:76 scale. The body is cast in metal with a painted finish and moul...

Rock & Tree Sliders mount along the sills to protect the lower bodywork and chassis from rocks and obstacles during off-road use, and give a be...

Fuel Tank Sender Wrench is a special service tool for the fuel tank sender unit assembly. It engages the metal locking ring that retains the fuel ...

Clutch Alignment Tool is a double-ended workshop tool for centring the clutch on manual transmission applications. During installation the tool ho...

Windscreen Brackets - a pair of CNC-machined billet aluminium brackets with a black anodised finish that secure the windscreen frame at its lower m...

Roof Access Ladder in a hot-dip galvanised steel finish, providing safe access to a roof rack. This is a non-drill (bolt-on) type ladder that moun...

Glazing rubber

Screw - Bonnet Hinge - M6 x 20 for the bonnet hinge assembly on the Defender. This M6 x 20 Torx-head screw secures the bonnet hinge. Used on vehic...

Heated Flat Mirror Head - the exterior door mirror assembly, fitted with a flat glass and an integrated heating element. The mirror head mounts to...

Bonnet for the Defender Puma era body assembly. This bonnet is taller and wider than the pre-2007 Defender bonnet, with a distinctive raised centr...

Clutch Slave Cylinder Repair Kit for the hydraulic clutch release circuit on V8 petrol applications. The clutch slave cylinder is actuated by hydr...

Hex-Head Bolt with a 7/16" UNF (Unified National Fine) imperial thread and a 2" shank length. A fastener used in the manual steering box mounting ...

Bolt with a 3/8" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing applic...

Bolt - M12 x 60mm is a metric hexagon head bolt used across a wide range of assembly applications on Land Rover vehicles. Thread specification M12...

Bolt - M10 x 130mm is a hex-headed metric fastener with a 10 mm nominal thread diameter and a 130 mm shank length. It serves as a general mounting...

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Rear door check assy LH

Check Assembly Door Rear - RH

Exterior Push-Button Door Handle for the front left-hand door. Mounted on the outer door skin, the handle forms part of the exterior door release ...

Steering Wheel Boss is a hub adapter that mounts a replacement steering wheel to the steering column. It engages a 36-spline column shaft and form...

Front Door Card is the interior trim panel that covers the inner structure of the front door, concealing the window regulator, latch linkage and wi...

Locking Nut for the steering linkage, securing the adjustable joint onto a heavy-duty drag link or steering rod. Once the joint is set to the corre...

heavy duty spring front RR/disco pair, like DA4201 and TF014.

Polyurethane Suspension Bush Kit A complete polyurethane bush set that replaces the original rubber suspension bushes across the chassis-mounted su...

Glass Retainer Kit for the rear safari door window - the aluminium retaining strips that hold the fixed glass in the door frame. The strips clamp ...

Sliding Window Pair - clear glass side windows within the body glazing, supplied as a pair. Each framed unit carries horizontally sliding clear gl...

Wing Protector - Long - 3mm Aluminium for the Defender front wings. Aluminium chequer-plate protector that mounts over the front wing tops of the ...

Pop Rivet - a blind (pop) rivet for fastening panels, trim and seals where access is available from one side only. The rivet is set with a hand or ...

Capping Corner Bracket forms the corner joint of the rear body capping trim. This left-hand bracket locates and secures the capping section at the...

Self-Tapping Screw, No.6 x 3/8". A self-tapping fastener that forms its own thread as it is driven, used to secure body panels, trim and light fix...

Anti-Roll Bar is the rear stabiliser bar within the suspension system, mounted transversely across the rear axle. Connected to the suspension thro...

Suspension Link Bush is the rear upper A-frame bush, fitted at the chassis-side mounting of the A-frame that locates the rear axle. It cushions an...

Crossmember - rear chassis crossmember for the body and chassis structure, supplied in the no-extensions configuration. It is the rearmost structur...

Rear Stop/Tail Lamp - Red is a 95mm round NAS-style rear lamp serving the combined stop and tail light function. It mounts to the rear body and co...