Land Rover Defender Parts

Rear Fog Switch for the dashboard switching circuit. A push-push type switch that controls activation of the rear fog lamp circuit. Mounts in the ...

ABS Pump Relay for the Anti-lock Braking System electrical circuit. A normally open, black-bodied relay that controls power supply to the ABS pump...

Bonnet Prop Stay the manual prop rod that holds the bonnet in the raised position. The stay props the open bonnet and locates in a catch to keep i...

Front door latch link

Floor Panel forms the main floor pressing on the left-hand (nearside) side of the body. This pressed-steel panel spot-welds into the body structur...

Front Main Floor Panel for the right-hand side of the cab floor structure. This panel forms the main front floor section on the right-hand side of...

Spring Nut - Metal U-Clip for body panel and electrical component fixings across a range of Land Rover models. This metal U-clip spire nut clips o...

Clip Nut - a spring clip nut for securing heater and air ducting components. It clips over a panel edge or flange to provide a threaded seat for a...

Nut - M10 is an M10 fixing nut for general assembly and repair use across the vehicle. It threads onto an M10 stud or bolt to secure a fastened jo...

Rear Window Catch Assembly, right-hand, for the side-opening rear window in the rear body. This catch latches the hinged rear side window to its f...

Catch Assembly for the side-opening rear cab window (5mm glass). Left-hand catch that secures the hinged side window in the rear body panel.

Vacuum Pump O-Ring that seals the diesel vacuum pump at its mounting joint. The vacuum pump supplies the depression used by the brake servo on die...

Rear Half Shaft - right-hand - for the Defender with early-type 23-spline CV joint. This solid steel drive shaft transfers torque from the rear di...

12-Point Bolt for the rear axle assembly on models fitted with the Salisbury axle. Secures a bracket to the axle case. The 12-point head allows a ...

Drive Screw is a countersunk-head self-tapping screw used to secure body and interior trim components. The self-tapping thread cuts its own mating...

PAS Pump Gasket Set for the cast-bodied power steering pump on the 3.5 V8. It provides the gaskets for resealing the pump when it is dismantled fo...

Self-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...

Pan Head Screw for use in the interior trim and body panel assembly of the Defender 90 and 110. This black-finished self-tapping pan head screw (N...

Screw - a No. 6 x 1" self-tapping screw used to secure interior and body trim. It fixes A-pillar trim, roof trim and body trim panels, forming its...

Output Shaft Bearing for the LT76 gearbox, a taper roller bearing that supports the rear output shaft. It locates the output shaft within the gear...

Brake Caliper Seal Kit for the rear 2-piston brake caliper with 41mm pistons. The kit renews the piston seals when the rear caliper is overhauled,...

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

Pan Head Screw - a 2BA x 1/2 inch slotted pan head fastener used across interior trim and body panel fixings. It retains interior trim panels and ...

Radiator Hose - the top hose of the engine cooling circuit, connecting the cylinder head outlet to the top of the radiator. It carries heated cool...

Distributor Drive Gear - V8

Rocker Cover Breather Hose - Left-Hand for the crankcase ventilation system of the Rover 3.5L V8 twin-carburettor engine. This hose connects the l...

Starter Motor Bush Kit for the diesel engine starter motor. The bushes carry the starter motor armature shaft in its end housings; renewing them r...

Vacuum unit

Front Stub Shaft forming part of the front axle assembly on the Series 3 Long Wheelbase (109"). The stub shaft sits within the swivel housing and ...

Steering Valve Ring is a PTFE sealing ring used within the rotary valve of the Adwest power steering box. It seals between the pressure lands of t...

Sedimentor Drain Plug Seal for the sedimentor in the diesel fuel supply. The sedimentor separates water and heavier contaminants from the fuel ahea...

Drive Belt for the air conditioning compressor, part of the accessory belt drive on the 3.5L V8 petrol engine. The belt transfers drive from the c...

Distributor O-Ring, the sealing ring for the ignition distributor on the 3.5L V8 petrol engine. The O-ring seals the distributor base where it loc...

Union Nut for the fuel pipe in the fuel delivery system. This M12 union nut clamps a fuel pipe to its mating union or component port, drawing the ...

Bolt & Lockwasher for securing the inlet manifold on the V8 petrol engine. Supplied as a bolt with its matching lockwasher. The imperial 5/16"...

Cylinder Head Bolt for the Rover V8 engine, 7/16" UNC thread. Used to secure the cylinder head to the block on the Rover 3.5L, 3.9L and 4.0L V8 en...

Cylinder Head Bolt - a 7/16" UNC x 2.71" medium-type bolt for the Rover V8, part of the cylinder head fixings. This is the medium-length head bolt...

Cylinder Head Dowel for the V8 petrol engine. The dowel is a locating pin fitted to the cylinder block deck that positively registers the cylinder ...

Engine Stud - a threaded manifold stud fitted to the exhaust system of the diesel engine. It threads into the cylinder head to provide a fixed anc...

Bolt

Mainshaft - Series 3

Oil Filter Gearbox

Layshaft Bearing for the early-type LT76 gearbox. It supports the layshaft (countershaft) within the gearbox, carrying the cluster gear that trans...

Fuel Pump Adaptor for mounting the external fuel pump on petrol engines. It provides the interface between the external fuel pump and its mounting...

Gearbox Gasket for the LT95 four-speed gearbox, sealing the power take-off (PTO) cover joint. Fits between the PTO cover and the gearbox main casi...

Ball Steel Bearing

Radiator Drain Plug seals the drain point in the cooling system and is removed to drain coolant during flushing or servicing. When fitted it close...

Exhaust Valve Guide is pressed into the cylinder head and supports the exhaust valve stem, keeping it accurately centred as the valve opens and clo...