Land Rover Defender Parts

Washer for use in general fastening applications across the Defender and Range Rover Classic. This plain washer distributes clamping load across t...

Needle Roller Bearing for the R380 manual gearbox. It carries the reverse idler on the layshaft, allowing the gear to rotate with minimal friction ...

Needle Roller Bearing for the manual gearbox mainshaft. The bearing carries a constant-mesh mainshaft gear, letting it spin freely on the mainshaf...

Fuse - 60A - high-current blade fuse for the main electrical protection circuits. Rated at 60 amps, this fuse protects high-draw circuits such as ...

Fan Cowl Clip is a retaining clip in the engine cooling system. It secures the fan cowl - the shroud that channels airflow through the radiator - ...

Bezel - Vent Air Louvre LH

Window Control Switch for the driver's door, in the double configuration. The switch is mounted in the driver's door armrest and operates the elec...

Idler Pulley for the auxiliary drive belt, 70mm diameter, positioned within the front-end accessory drive system. The pulley guides and stabilises...

Seatbelt Anchorage - Upper - RH for the Defender seatbelt system. This structural bracket mounts to the pillar or roof structure at the top of the...

Seatbelt Anchorage - Upper - LH for the Defender seatbelt system. This structural bracket mounts to the pillar or roof structure at the top of the...

Heater Valve for the cabin heating circuit on Defender Puma diesel models from 2007 onwards. This valve regulates the flow of engine coolant to th...

Door Card - Push Button - Electric - RH is the interior trim panel for the right-hand front door. It covers the inner door frame to provide the fi...

Door Card - Push Button - Electric - LH is a left-hand interior door trim panel incorporating a push-button door release and electric window switch...

Name plate Front Brunel NDER

Lock Nut for the front output shaft, used in the transfer box assembly. This nut secures the front output shaft drive flange within the transfer b...

Screw - a fastener used to secure exterior body panels and trim, including body mouldings, front and rear bumper assemblies, radiator grille panels...

Air Intake Hose from the air cleaner assembly of the 2.5 Turbo Diesel engine. It ducts filtered air from the air cleaner housing to the turbocharg...

Needle Roller Bearing - supports the worm and input shaft within the manual (non-power-assisted) steering box of the Gemmer type. It locates the w...

Heater Blower Motor and Fan Assembly - the powered fan unit of the cabin heating, ventilation and demisting system. The electric motor drives the ...

Fuel Pump Gasket seals the external fuel pump to its mounting face in the fuel delivery system, preventing leakage at the joint. Used on petrol ap...

Snorkel Head is the 3" ram-air intake head that fits to the top of a raised air intake tube, forming the forward-facing scoop that feeds cool, clea...

Washer - M4 flat washer, used to spread the clamping load of an M4 fastener and protect the panel surface beneath the fixing. Fitted at a number o...

Front Shock Absorber Turret: the tubular mounting tower that locates the upper end of the front damper. It bolts to the chassis and provides the t...

Conrod

Spare Wheel Carrier Hinge Bush - a pair of nylon bushes for the swing-away spare wheel carrier (DA2232 / GA2232). The bushes line the hinge pivot ...

adjuster for door latch, push-button doors only

Snap Ring used within the LT95 4-speed gearbox to retain the inner member to the mainshaft. The LT95 is the 4-speed gearbox with integral transfer ...

Sunroof Handle Assembly operates the manually-operated glass sunroof, forming the interface between the occupant and the roof panel's opening mecha...

A-Pillar Grab Handle - an interior assist handle for the windscreen (A) pillar, finished in silver. Gives front occupants a hand-hold to aid entry...

Layshaft Bearing is the layshaft taper roller bearing for the LT77 and R380 5-speed manual gearbox. Located in the gearbox centre plate, it suppor...

Gearbox Mainshaft is the central output shaft of the LT77 5-speed manual gearbox, running the full length of the transmission from the input end to...

Synchromesh Assembly for 1st and 2nd gear in the LT77 5-speed manual gearbox. Mounted on the mainshaft, the synchromesh matches the rotational spe...

Upper Steering Column Shroud is the moulded cover fitted over the top section of the steering column. It encloses the upper column and the mountin...

Fuel Pipe for the fuel supply circuit, running to the carburettor. It carries fuel from the fuel pump outlet to the carburettor inlet on the 2.25L...

Rear Body Seal is a rubber seal fitted to the rear body extension panel of the station wagon body. The seal closes the gap between the extension p...

Steering Boss Adaptor - a mounting adaptor between the steering column boss and an aftermarket steering wheel. It adapts the fixing pattern of the...

Brake Union - Blanking Plug, male thread, M10 x 1mm, short body. Used in the metric hydraulic brake circuit to blank off an unused or redundant po...

Buffer Rubber for the rear end door check mechanism. The buffer forms the end-stop in the lever-type rear door check strap assembly. It absorbs co...

Layshaft is the countershaft within the R380 five-speed manual gearbox, carrying the cluster of gears that mesh with the mainshaft gears. Drive pa...

Engine Oil Dipstick for the 300TDi 2.5L turbo diesel engine. Locates in the dipstick tube on the engine block and provides the oil level reference...

Mud Flap Bracket for the left-hand rear position on High Capacity Pick Up (HCPU) bodywork. Part of the exterior mud flap mounting. The HCPU rear b...

Baulk Ring for the LT77 5-speed manual gearbox synchromesh assembly. The baulk ring is the friction cone element of the synchromesh unit. It conta...

Exhaust Manifold for the 2.5-litre four-cylinder naturally aspirated diesel engine. It bolts to the exhaust ports of the cylinder head, collecting ...

5th Gear - LT77 is the mainshaft-mounted overdrive gear for the LT77 5-speed manual gearbox, located at the rear of the transmission in the 5th-gea...

Exhaust rear silencer LR90 def TD5 Stainless steel

Gear Lever Boot - a flexible gaiter that seals around the base of the gear-change lever where it passes through the transmission tunnel. It closes...

Differential Pinion Bearing Shim - 0.066 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Bolt, high tensile, M8 x 25mm. A metric hexagon head bolt for body, chassis, and structural fastening applications.