Land Rover Defender Parts

Setscrew used as a general-purpose fastener in engine bay ancillary and drivetrain assemblies. Applied at engine harness mounting points, bell hou...

Front Radius Arm Assembly for the front live axle in a coil-spring suspension arrangement. The radius arm runs longitudinally between the axle and...

Diff Pinion Taper Roller Bearing is the inner pinion taper roller bearing in the Salisbury axle differential. It supports the pinion shaft where i...

Brake Lining - Rear is a replacement friction lining for the rear drum brake assembly on long-wheelbase Land Rover models, covering 109-inch, 110-i...

Bearing Needle Non-Powerstr. Box Input

Selector Roll Pin for the LT77 and R380 5-speed manual gearboxes. The roll pin secures a selector fork to its selector shaft, locking the two toge...

Heat Shield - Engine Mount for the Puma diesel engine mounting assembly. This shield mounts over the engine mount rubber to protect it from heat a...

Exhaust Manifold - LH End Section for the 300TDi 2.5L inline 4-cylinder turbo diesel engine. Forms the left-hand (longer elbow) section of the two...

Brake Pipe Bracket secures and locates a rigid brake pipe within the braking system's pipe routing. Mounted to the chassis, it clamps the brake li...

Turbo Hose is the charge air transfer hose connecting the intercooler outlet to the inlet manifold on the Defender 2.5L Turbo Diesel engine. Follo...

Banjo Bolt for the turbocharger oil feed pipe on the Td5 engine. This M12 x 1.0mm thread banjo bolt clamps the hollow banjo fitting of the oil sup...

A/C Receiver Dryer

Bolt - M6 x 55mm hex head bolt used in braking system assemblies. Standard metric hex fastener supplying clamping force in brake-related mounting ...

Honeycomb Grille for the front panel assembly, providing a restyled honeycomb-pattern front face as a direct replacement for the standard grille. ...

Breather Tube for the LT230 transfer box. This tube forms part of the breather system on the LT230 transfer gearbox, routing pressure venting away...

Front Bumper End Cap - Outer, installed at the outer section of the front bumper assembly. This component forms part of the Front Bumper & Bum...

Speedometer for the instrument cluster, displaying road speed with LED illumination. It mounts in the dashboard instrument panel, indicating vehic...

Service Filter Kit for the 200 TDi 2.5L turbo diesel engine, grouping the filters and sealing washers required for a routine engine service under a...

Fuel Pipe - Tap to Tank - a fuel line in the low-pressure diesel supply circuit, running between the fuel tank and the fuel tap. It carries fuel f...

Front Wheelarch is a body panel that forms the wheel housing around the front wheel on the right-hand (RH) side. It encloses the upper and rear fa...

Front Propshaft - Wide Angle, connecting the transfer case front output flange to the front axle differential input pinion. The wide angle joint d...

Second Row Door Hinges for the rear side door apertures of the body assembly, supplied as a set of four in stainless steel. These hinges replace t...

Circlip is a split retaining ring that locates on the reverse shaft of the LT95 gearbox. It seats into a machined groove to axially retain the rev...

Blanking Plug for the cylinder block. It seals a machined port in the engine casting where no sensor, sender or fitting is installed, preventing co...

Handbrake Carrier Spacer for the handbrake assembly on Series II, IIA, III and Defender 90/110. This spacer fits within the handbrake carrier mech...

Split Pin for the rear tailboard lower assembly. A split pin (cotter pin) passes through a drilled clevis or retaining pin and its legs are splaye...

Power Steering Pump Spigot - the locating spigot that mounts and centres the Adwest power steering pump on the engine front ancillary drive. It pr...

Coupling Assembly - union fitting for the engine oil cooler pipe circuit. This union connects adjacent oil cooler pipe sections in the engine bay,...

Mainshaft Spacer - a spacer fitted to the gearbox mainshaft of the five-speed manual gearbox. It sets the axial position of the gears and bearings...

Gearbox Selector Circlip - a retaining circlip within the manual transmission gear selector mechanism. The circlip locates on its shaft to secure ...

Mainshaft Bearing

Rubber Washer - Seat Backrest for Land Rover Series and Defender models. This rubber washer is used in the seat backrest assembly, fitting beneath...

Mainshaft Nut Staked retaining nut securing the shaft assembly within the manual gearbox. Tightened and staked to lock the gearbox shaft component...

Shim

Oil Pump Repair Kit - renews the oil pump of the LT77 and LT85 five-speed manual gearbox. The pump is housed in the gearbox extension casing and ci...

Thrust Washer and Pin for the LT95 four-speed gearbox, 3.55mm thickness. This selective-thickness washer, with its locating pin, sets the end-float...

Rear Radius Arm Bush Kit - Chassis End, supplied as a set of four polyurethane bushes with retaining plates, inner sleeves, and installation grease...

Flexible Brake Hose for the front hydraulic braking circuit. It carries brake fluid pressure between the rigid chassis-mounted brake pipe and the f...

Seat Belt Assembly is an individual rear seat belt, part of the rear seat occupant restraint assembly. It serves one inward-facing rear seat posit...

Bush Kit - Front Radius Axle Arm End

Headlamp Bezel Clamp from the front headlamp mounting assembly. The clamp secures the headlamp bezel to the lamp mounting panel, retaining the lig...

Selector Fork for the 3rd and 4th gear positions in the five-speed manual gearbox (LT77 and R380). The fork engages the 3rd/4th synchro hub sleeve...

Key Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...

Distributor - 3.5L V8 Twin Carb is the ignition distributor for the Rover 3.5L V8 petrol engine in twin-carburetter configuration. The distributor...

Piston Ring Set for the 300 TDi diesel engine, supplied in standard size. The set provides the compression and oil control rings for one piston. F...

Shock Absorber for the front suspension — the hydraulic damper that controls spring movement at the front axle. The damper resists and slows the c...

Front Half Shaft for the left-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant velo...

Rear Brake Pad Set for the rear disc brakes, part of the hydraulic braking circuit. The pads are clamped against the rear brake disc by the caliper...