Land Rover Defender Parts

Weatherstrip for the alpine light (side roof window) glass. This rubber sealing strip retains and seals the 5mm glass panels of the alpine lights ...

Fuel Pump Gasket for the 2.0L diesel engine (Series II) and 2.25L diesel engine (Series IIA). This gasket seals between the mechanical fuel pump b...

Bolt - 3/8" BSF x 1" hexagonal head bolt to British Standard Fine thread specification. 3/8" BSF (British Standard Fine) thread with a 1" shank le...

Shock Absorber for the front suspension on the short-wheelbase (SWB) chassis. Mounted between the front axle and the chassis, the hydraulic damper...

Spark Plug - ignites the air/fuel mixture in the combustion chamber of the petrol engine. It threads into the cylinder head with its electrode gap ...

Glass Run Channel for the door window aperture, supplied in a 2 m length. The channel lines the door frame to guide and seat the side window glass...

Injector O-Ring for the 2.5L Td5 5-Cylinder Turbo Diesel fuel injection system. This O-ring seats in the groove on the injector body at the cylind...

Bulb Holder - double-filament bulb holder for an exterior lamp assembly, accepting a 5/21W (P21/5W) twin-filament bulb. The holder seats into the ...

Oil drain plug TD5

Timing Belt Kit with Tensioners for the 300 TDi 2.5L turbo diesel engine. The kit serves the timing belt drive - the toothed-belt system that synch...

Brake Pad Set for the rear axle disc brakes, fitting the rear brake calipers. The friction pads clamp against the rear brake discs under caliper a...

Lock Washer for the gearbox mainshaft, securing the special retaining nut where the mainshaft meets the transfer box. A tab washer whose tang is b...

Rear Upper Shock Absorber Bracket, the upper mounting bracket for the rear damper within the rear suspension. It forms the fixed upper anchorage b...

Thermostat for the engine cooling system, with an 82°C opening temperature. The thermostat regulates coolant flow between the engine and the radia...

Oil Filter Rotor is the rotating element of the centrifugal oil filter on the Td5 2.5L 5-cylinder turbo diesel engine. Mounted within the centrifu...

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the Rover V8 petrol engine. It forms a coolant-tight joint bet...

Vacuum Pump Gasket for the 2.5L 300TDi diesel engine, sealing the vacuum pump mounting face to the cylinder block. The vacuum pump is driven from ...

Coolant Bypass Hose for the thermostat assembly on the 3.5L V8 petrol engine. This hose connects the thermostat housing to the inlet manifold, pro...

Shim hinge

Panhard Rod Bolt - a metric hexagon-head bolt measuring M14 x 80mm, used to secure the Panhard rod within the axle location. The Panhard rod locat...

Carburettor Inlet Seal for the Zenith carburettor, in the engine air intake system. It seals the joint between the carburettor air intake and the ...

Brake shoe spring 109 rear lower

O-Ring - an elastomer seal used at the oil cooler pipe connection within the engine oil cooler circuit. It seats in the union between the oil cool...

Fuel Tank Mounting is the moulded rubber isolator in the fuel tank mounting assembly that sits between the tank body and its chassis support. It c...

Grease Nipple with a short thread, used at propshaft universal joint lubrication points. The nipple threads into the grease point and provides the...

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Detent Spring for the manual gearbox gear selector mechanism. The spring loads the detent ball against the selector shaft, holding the selected ge...

Brake pad kit rear

Hub Oil Seal - Inner for the front and rear wheel hubs, seating around the stub axle. The seal runs on the stub axle to retain hub lubricant and e...

Headlamp for the front exterior lighting system, configured for left-hand-drive vehicles (right-hand traffic). The unit houses the halogen bulb an...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Windscreen Wiper Motor for the front wiper system, supplied as a motor assembly with the integral reduction gear and park switch. Supplied without ...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Distributor Module for the 3.5L Rover V8 petrol engine, used with the earlier single-coil electronic ignition system. It forms part of the distribu...

Screw with a 1/4" UNF (Unified Fine) thread, 7/8" long, used as a setscrew in body, hinge and mirror-arm fixings. Note: non-metric (imperial UNF) ...

Alternator - charging unit in the vehicle's electrical charging system. Driven from the engine by the accessory belt, it generates current to powe...

Rotor Arm for the Lucas distributor in the ignition system. Mounted on the distributor shaft beneath the cap, it routes the high-tension spark fro...

Flasher Relay installed in the indicator and hazard-warning circuit, controlling the flash rate of the turn-signal lamps. This 12V electronic unit...

Self-Locking Nut with a 5/16" UNF thread and a 1/2" across-flats hexagon. The self-locking action resists loosening under vibration, retaining cla...

Brake master cylinder

Hex Nut - 1/4" UNF is a plain hexagonal nut with a 1/4 inch UNF thread, used as a general-purpose imperial-thread fastener throughout the chassis, ...

Captive Nut with a UNF thread, providing a fixed threaded anchor point for a bolted fixing. The nut is retained in its bracket or panel so it cann...

Wheel Bearing Kit - a complete single-hub kit containing the bearings, seal and fixings to rebuild one wheel hub, suitable for either a front or a ...

Clutch Slave Cylinder Push Rod within the Clutch Actuation Assembly, transmitting hydraulic force from the external slave cylinder to the clutch re...

Glow Plug for the 200TDi and 300TDi 2.5-litre direct-injection turbo diesel engines. It forms part of the cold-start pre-heating system. The glow ...

Gear Knob - gear lever knob for the R380 5-speed manual gearbox. Threads onto the gearchange lever, forming the driver's hand grip and gear-select...

Brake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...

Power Steering Pressure Hose - LHD for the power steering hydraulic circuit. This high-pressure hose connects the power steering pump outlet to th...