Land Rover Defender Parts

Half Shaft Shim is a 1.50mm selective shim used in the axle drive shaft and hub assembly. It sets the endfloat of the half shaft drive member with...

Front Brake Disc Shield - Defender This pressed-steel shield fits behind the front brake disc on the Defender, located between the disc and the sw...

Synchro Cone (Baulk Ring) - LT95 4-Speed Gearbox This synchro cone, also known as a baulk ring, is a component of the synchroniser assembly within...

Needle Bearing - LT77 5-Speed Gearbox - Mainshaft This needle roller bearing supports the mainshaft gear cluster within the LT77 5-speed manual ge...

Needle Bearing - LT77 supports a mainshaft gear on the LT77 5-speed manual gearbox mainshaft, allowing the gear to rotate freely on the shaft. It ...

O-Ring - Diff Lock Selector Shaft - LT230 Transfer Case This O-ring seals the differential lock selector shaft where it passes into the LT230 tran...

Gasket

Clutch Release Arm Pivot Plate for the LT77 5-speed manual gearbox. Mounts inside the clutch bellhousing and provides the pivot point for the clut...

Front Cover to Gearcase Gasket seals the joint between the front cover and the main gearcase on the LT77 5-speed manual gearbox. This gasket preve...

Breather Assembly vents the front axle housing, letting trapped air escape and equalising internal pressure as the differential oil heats and cools...

Gearbox Oil Seal for the extension case of the LT77 five-speed manual gearbox, sealing the mainshaft output collar. The seal runs on the collar at...

Speedometer Drive Gear sits on the output shaft of the LT230 transfer box and forms part of the speedometer drive, transmitting shaft rotation to t...

Drive Meter Speedo Gear Yellow 22 Teeth

Speedometer Drive Gear - 21 Teeth - Green is the drive pinion in the speedometer drive assembly located on the LT230 transfer box output housing. ...

Rear Prop Shaft for V8 petrol applications. The propeller shaft sits in the driveline and transmits drive from the transfer gearbox rear output to ...

Gearchange Housing Gasket for the LT85 five-speed manual gearbox. This gasket seals the interface between the gearchange housing and the main gear...

Dowel is a precision locating pin that aligns mating components during assembly, setting their position accurately and relieving the securing bolts...

Rear Left-Hand Half Shaft for the 10/24 spline rear axle. The half shaft transmits drive from the differential to the rear wheel hub. This left-ha...

Rear Axle Half Shaft - right-hand, 10/24 spline, for the Series III rear axle. This shaft transmits drive from the rear differential to the rear wh...

Differential Pinion Bearing Shim - 0.070 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Flanged Nut - M6 flanged hex nut for use across a wide range of Land Rover assemblies including engine, drivetrain, body, braking, and electrical a...

Rear Seat Belt Puma - 110

Oil pump relief valve washer V8

Piston for the 2.5L four-cylinder turbo-diesel engine, operating within the cylinder block as part of the piston and connecting-rod assembly. The ...

Dowel Ring locates the cylinder head to the block deck on the 200 TDi and 300 TDi diesel engines. Seated in the block face at the head-to-block jo...

Carburettor for the 2.5L petrol engine, mounted on the intake manifold within the fuel delivery system. It meters and atomises fuel into the incom...

Exhaust Manifold for the 3.5L V8 petrol engine, supplied without heat transfer cover. The manifold collects exhaust gas from one cylinder bank and...

Injector Clip for V8 EFI fuel injection systems, used in the fuel delivery assembly at the intake manifold. This retaining clip secures the fuel i...

Exhaust Valve for the 2.25L 4-Cylinder Petrol engine, fitted in the cylinder head valvetrain assembly. This valve operates in the cylinder head to...

Power Steering Pump Pulley for the power steering hydraulic circuit. The pulley mounts on the power steering pump shaft and is driven by the auxil...

Flywheel - 5-Bearing is the rotating mass mounted to the rear flange of the crankshaft in the 5-main-bearing variant of the 2.25L and 2.5L 4-cylind...

Piston Cooling Oil Jet Relief Valve - part of the engine lubrication system, fitted in the cylinder block oil feed to the piston cooling jets. It r...

Injector Pipe Clip for the diesel fuel injection system. The clip secures and spaces the high-pressure injector pipes, damping vibration and preve...

Valve Cotter in the cylinder head valvetrain, locking the valve spring retainer to the valve stem. The cotters seat as a pair into the machined gr...

Valve Spring Cap for the cylinder head valve train. The spring cap seats on top of the valve spring and locates against the split collets on the v...

Inlet Valve for the cylinder head valve train, with a 34.5 mm head diameter. The inlet valve opens on the induction stroke to admit the air/fuel c...

Radiator assembly

Fuel Pipe for the 200 TDi diesel fuel delivery circuit. Connects the fuel filter outlet to the injection pump inlet, carrying filtered fuel to the...

Exhaust Downpipe with Cat is the front section of the exhaust system for the 300TDi engine, incorporating the catalytic converter. It bolts to the...

Bracket

Upper Radiator Mounting Bracket that locates and secures the top of the radiator in the cooling system. Fitted to four-cylinder TDi and Td5 applic...

Fuel Tank Bracket for the fuel tank mounting assembly on the Defender. This steel bracket secures the fuel tank to the chassis, forming part of th...

Exhaust Front Pipe Bracket supports and locates the front section of the exhaust system. It secures the front exhaust pipe at its mounting point a...

Centre Silencer for the exhaust system on the Defender 90 with 300TDi engine. Fitted in the mid-section of the exhaust run between the downpipe an...

Oil Cooler Pipe - To Engine for the engine oil cooling circuit on 2.5L 4-Cylinder diesel applications. This pipe forms the return leg of the oil c...

Hose

Front Exhaust Pipe for the Defender equipped with the naturally-aspirated 2.5L diesel engine. This downpipe connects the exhaust manifold outlet t...

Oil Cooler Adaptor Gasket for the Rover V8 petrol engine, part of the engine lubrication circuit. It seals the joint between the oil cooler adapto...