Land Rover Defender Parts

Upper Rear Door Seal, the rubber weatherseal for the top edge of the rear door aperture. It seals the upper line of the rear door against the body...

Front Door Check Strap, part of the front door hinge and retention hardware. Connecting the front door to the body pillar, the check strap limits ...

Door Latch Shim - Rear - a packing shim for the rear door anti-burst latch, part of the door lock and handle assembly. Fitted behind the latch on ...

Engine Plug is a core (welch) plug that seals the casting holes in the engine. Fitted to the cylinder block, cylinder head water jacket and inlet ...

Seat Base Corner Capping in plastic. Fitted at the outer corners of the front seat base frame, this capping provides a neat finished edge and prote...

Heater Control Mounting Plate for left-hand drive applications. Fitted within the heater control assembly in the cab interior, this plate provides ...

Sill Panel Rear 109 Not Station Wagon - LH

Rear Sill Panel for the right-hand side of the body understructure on long wheelbase (109 inch) models. Fitted at the rear sill position, this pane...

Heater Air Intake Trim fits the front wing air intake of the heating and ventilation system. It finishes the fresh-air intake aperture in the wing...

Steering Column Top Clamp secures the upper section of the steering column at its top support within the steering column assembly. It clamps the c...

Edge Clip - Door Lock Mechanism with various applications across Land Rover Series, Defender, Discovery 1, and Range Rover Classic models. This sp...

Door lock RH

Blanking Plug is a rubber grommet used to seal unused 1-inch (25.4 mm) diameter holes in body panels, bulkheads and floor sections. The plug press...

Clevis Pin for the bonnet stay. Forms the pivot at the upper end of the bonnet prop, retaining the stay to the bonnet.

Check rod RH

Fitment: all models to 1980

Plain Washer - 7/16" used in the power steering box assembly. This flat washer is used within the steering hydraulic assembly at the power steerin...

Inner Seat Base is the centre front seat base cushion, forming the lower seating platform of the basic vinyl front seat. Finished in black vinyl f...

Barrel Lock and Key, Set of Three for the door locks, supplied as three keyed lock barrels each with a key. Each barrel is the cylinder the key tu...

Lower Tailgate for the rear of the body - the drop-down tailboard panel that closes off the rear of the load area. Hinged along its lower edge, it...

Rope Hook - a securing hook for the canvas hood (soft top). It provides an anchor point around which the hood tie-down rope is passed, holding the...

Washer

Hinge Pin - the pivot pin for the top hatch (windscreen) hinge. It passes through the hinge knuckles to retain the two halves of the hinge while a...

Intermediate Shaft

Rocker Bracket Locating Dowel for the cylinder head and rocker assembly in the 2.25L and 2.5L petrol and diesel engines. This dowel locates the ro...

Timing Chain Tensioner maintains correct tension on the timing chain within the engine timing case, preventing chain slap and ensuring accurate val...

Oil Feed Pipe is the external oil feed pipe supplying the cylinder head within the engine lubrication system. It carries pressurised oil from the ...

Top cover

Ball Race - Steering Box (Adjusting) is a component of the recirculating-ball manual steering box assembly, used to control pre-load and end-float ...

Mainshaft Thrust Washer - 2nd Gear (0.125") is a selective shim located within the Series gearbox, fitted to control axial play on the second gear ...

Spring - Timing Ratchet sits within the engine timing assembly on Land Rover 2.25L and 2.0L diesel engines. This spring provides the retention for...

Bolt - 5/16" UNF x 5/8" is a general-purpose hexagon-head set bolt in 5/16 UNF (Unified National Fine) thread, 5/8 inch in length. Used across engi...

Manifold Stud is used to secure the combined inlet/exhaust manifold assembly to the cylinder block on Series vehicles fitted with the 2.25L diesel ...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Timing Chain Tensioner Spring for Land Rover 2.0L Diesel and 2.25L Petrol and Diesel four-cylinder engines. This spring applies constant pressure ...

Sealing Ring - Rocker Cover Breather Bolt for the 2.25-litre 4-cylinder engine. This sealing ring is fitted under the rocker cover breather bolt, ...

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Stud for use in Land Rover gearbox assembly.

Mainshaft Bearing for the gearbox mainshaft - the centre bearing that supports the mainshaft within the gearbox casing. It locates and carries the...

Mainshaft Bearing for the gearbox mainshaft - the centre bearing that supports the mainshaft within the gearbox casing. It locates and carries the...

Braided Earth Strap with Battery Clamp - 300mm for the vehicle electrical grounding circuit. This braided copper earth strap is fitted with an int...

Wheel Hub Assembly for the front and rear axle knuckle assembly. This wheel hub assembly mounts to the steering or rear knuckle and houses the whe...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Valve - Control

Front Suspension Bolt - a mounting bolt used in the front suspension assembly, at the suspension arm and knuckle/hub mountings. It secures the joi...

Underbody Guards - 6mm Alloy for the Land Rover Defender (L663, 2020+). Manufactured from 6mm-thick aluminium alloy, these guards fit directly to ...

Rock Sliders with Tree Bars for the Land Rover Defender 110 and 130 (L663, 2020+). Constructed from steel box section and finished in black powder...

Timing Chain Kit for the Ingenium 2.0L 4-cylinder engine, covering the complete timing chain system. The Ingenium AJ200 engine uses a dual-chain a...